The main document regulating urban planning activities in Russian Federation, is the Town Planning Code(Further - GrK). It defines all its legal aspects - from the procedure for conducting engineering surveys to putting the facility into operation. It also describes the procedure for developing, agreeing and approving project documentation for buildings, structures and linear objects.
All construction works are classified in a certain way, their misinterpretation can lead to financial losses or other undesirable consequences. One of the most controversial issues is the subject of discussion of this article.
So, let's look at the definitions of the concepts overhaul and reconstruction:
Reconstruction of objects capital construction (Article 1, Clause 14 of the GrK) - changing the parameters of an object or its parts (height, number of floors, area, volume), including a superstructure, rebuilding, expansion, as well as replacement and (or) restoration of load-bearing building structures, with the exception of replacement of individual elements of such structures with similar or other elements that improve the performance of such structures and (or) restoration of these elements;
The definition of the reconstruction of linear objects can be found in article 1, clause 14_1 of the GrK.
Capital repairs of capital construction facilities(Article 1, clause 14_2 of the GrK) - replacement and (or) restoration of building structures of an object or elements of such structures, with the exception of load-bearing building structures, replacement and (or) restoration of engineering support systems and engineering networks or their elements , as well as the replacement of individual elements of load-bearing building structures with similar or other elements that improve the performance of such structures and (or) the restoration of these elements.
The definition of the overhaul of linear facilities can be found in article 14_3 of the GrK.
The main feature of the reconstruction work is the need to develop a complete set of project documentation, which includes all the mandatory sections according to Decree of the Government of the Russian Federation No. 87.
Also, in most cases, it will be necessary to conduct its examination.
In addition, you will have to obtain a building permit, in the event that structural elements or other characteristics of the reliability and safety of the object are affected, as well as the maximum permissible construction parameters are exceeded during the performance of work (part 17.4 of Article 51 of the Civil Code).
If it is necessary to obtain a building permit, it is also necessary to put the facility into operation after completion of work.
The procedure for preparing documentation for reconstruction is in many ways similar to the development of such documentation for new construction.- You will have to go through the same steps. You can read more about this in the article “Project documentation”, which describes the composition of stage P, the need for its development for various objects, the procedure and features of passing state and non-state examinations, as well as other nuances.
When carrying out a major overhaul, in accordance with paragraph 12_2 of article 48 of the GRC, it is necessary to develop only those sections of the project documentation that affect the work performed. In addition, in accordance with paragraph 2 of Article 51 of the Civil Code, in this case no building permit is required.
It also does not require commissioning of the facility upon completion of work.
Note that the attribution of works to one or another type is within the competence of the owner of the object or the person responsible for its operation. This also affects Accounting the specified person, but this is a topic for a completely different article and will not be considered here.
Carrying out reconstruction work without a building permit or under the guise of a major overhaul is punishable by law. In accordance with part 1 of article 95 of the Code on administrative offenses for these actions, legal entities are subject to a fine of 500,000 to 1 million rubles or an administrative suspension of activities for up to 90 days.
To begin with, we note that at least one sign indicated in the definition of the concept of "reconstruction" is enough to classify works as this type.
For example, the following types of work will be classified as reconstruction:
According to the definitions of these concepts, the difference lies in the number of structural elements to be replaced.
Overhaul - replacement of part of the supporting structures or their individual elements. De jure, when replacing 99% of the beams, we can say that this species work is a major overhaul. Thus, you do not need to develop a complete set of project documentation in accordance with Decree of the Government of the Russian Federation No. 87, obtain a building permit and put the facility into operation.
The criteria that determine the line between the reconstruction and overhaul of linear facilities are: changes in the class, category, initially established performance indicators of the facility, changes in the boundaries of the right of way or protected zones.
In this article, we will not consider in detail the nuances of the reconstruction and overhaul of linear facilities and will limit ourselves to giving one classic example: if you are going to build any facility next to a highway (gas station, car wash, etc.), then you will have to make entrances from it and ramps that are highly likely to affect throughput. Also, the right-of-way may change. Therefore, sometimes formally, legally, during the construction of such facilities, it is necessary to reconstruct a linear facility.
Species list construction works, for the implementation of which it is necessary to obtain permission from the SRO
I. Types of work on engineering surveys
1. Work on the implementation of engineering and geodetic surveys
2. Work on the implementation of engineering and geological surveys
3. Work on the implementation of engineering and hydrometeorological
research
4. Work on the implementation of engineering and environmental surveys
5. Work on the implementation of engineering and geotechnical surveys
6. Work on the survey of the state of soils of the foundations of buildings and
structures, their building structures
II. Types of work on the preparation of project documentation
1. Work on the preparation of a scheme for the planning organization of a land plot
2. Work on the development of architectural solutions
3. Work on the development of structural and space-planning solutions
4. Work on the preparation of information about engineering equipment, engineering and technical support networks, a list of engineering and technical measures, the content of technological solutions
5. Work on the preparation of a construction organization project
6. Work on the preparation of a project for the organization of work on the demolition or dismantling of objects
7. Work on the development of environmental protection measures
8. Work on the development of measures to ensure fire safety
9. Work on the development of measures to ensure access
disabled people
10. Works on the preparation of the design of the right of way of the linear facility
11. Work on the development of technological and design solutions
linear object
12. Work on the preparation of materials related to the provision
security of buildings and structures, as part of the section "Other
documentation in cases stipulated by federal laws"
III. Types of works on construction, reconstruction, overhaul
1. Preparatory work at the construction site
Arrangement of electric lighting systems for temporary buildings
Installation of temporary protective fences
Crane runway arrangement
Construction of single-track rail tracks
2. Demolition and demolition works
Breaking walls, arrays, ceilings, punching nests
Disassembly of the ground part industrial buildings
Dismantling of reinforced concrete flights of stairs, platforms and steps
Disassembly of window, door and gate openings, partitions and suspended ceilings
Dismantling of sidewalks, floors, roofing and cladding
Dismantling of industrial furnaces
Dismantling of the lining of tunnels from cast-iron tubing
Dismantling of metal columns, beams and frames
Dismantling of contact network supports
3. Works on dewatering, organization of surface runoff and drainage
The device of water supply and drainage ditches
Device for drainage from trenches and pits when working in wet soils
Closed drainage device
Immersion and extraction of wellpoints and sprinkling of filter materials
Assembly and dismantling of the suction manifold
Construction of structures made of stone and rock
Backfilling with sand or slag using mechanisms
Construction of underlying layers and foundations made of sand and gravel
The device of underlying layers and bases from crushed stone
The device of drainage layers and filters from crushed stone (coal)
The device of drainage filters from gravel and sand
Laying of porous ceramic plates of aerates
4. Works on the development of recesses, vertical planning
Soil development by excavators in excavations, pits, trenches and dump or embankment
Soil excavation by excavators with loading onto railway or road transport and export
Development and movement of soil by bulldozers
Development and movement of soil with scrapers
Mechanized digging
Development and movement of soil under the influence of hydraulic structures
Paving slopes with stone and slabs with stops
Strengthening drainage channels with trays - gutters, boards, shields and mats with heads
5. Embankment and backfilling works
Backfilling of soil manually with compaction by electric or pneumatic rammers
6. Hydromechanized and dredging works
Development and movement of soil by jet and floating dredgers
Loosening and development of soils under water in a mechanized way and issuance to a dump or floating facilities
Loosening the soil under water with jackhammers and divers
Loosening of frozen soil with a wedge - a woman, rippers and drilling rigs
Digging trenches with an excavator and ditcher
7. Explosive work
Explosion of rocky soils, crushing of boulders and oversized pieces
Explosion of mass soils for ejection and discharge
Loosening frozen soils
Shelter of the blasted area to protect structures
Compaction of soil under water by explosions
8. Work on the installation of pile foundations, sheet piling, anchors
Insertion of reinforced concrete piles
Immersion of reinforced concrete sheet piling on the quays
Driving steel piles in permafrost
Driving and retrieving steel and sheet piles
Driving wooden and wood-metal piles with sheet piling
Installation of bored piles with drilling of wells and filling of hollow piles with concrete
Device for disassembling tongue-and-groove wooden lintels
Installation of metal guide frames and underwater ties for sheet pile driving
9. Works on compaction of soils of natural occurrence and arrangement of soil cushions
Leveling the territory of the irrigated area with mechanical rolling
Soil compaction with heavy rammers
Soil compaction with rollers and compactors
10. Works on the construction of sinkholes and caissons
Lowering a well with mechanized excavation
Lowering the well manually
11. Works on the construction of structures using the "wall in the ground" method
12. Works on fixing soils
Strengthening thermal soils
Cementation of soil bases with driving injectors
Silicization and resinization of soils
13. Works on artificial freezing of soils
14. Concrete work
Installation of metal mesh formwork
Installation and dismantling of panel formwork
Installation and dismantling of wooden scaffolds, piers and formwork
Installation of reinforcement for monolithic reinforced concrete structures
Installation of reinforced meshes, reinforcement cages, armored trusses, reinforcing structures with a concreted lower chord in hydraulic structures
Installation of anchor bolts and embedded parts
The device of the bases and underlying layers
The device of rubble concrete and concrete foundations
Installation of concrete columns and rack supports
Installation of concrete walls and partitions
Arrangement of supports, plugging of wells and shafts
Concrete under water
Foundation grouting for equipment
Fastening walls and vaults of workings with shotcrete and sealing joints in vaults of frame supports
Preparation of concretes and mortars
Installation of reinforced concrete foundations, stops, retaining walls, rack supports
Installation of monolithic channels, tunnels, trays, bottoms, galleries
Arrangement of structures of a sink well, thickeners, baths, pools, capacitive structures of water supply and sewerage
Arrangement of tower-type structures of silos, cooling towers, towers, pipes
Arrangement of reinforced concrete lining of tunnel shafts, shaft bottoms, waterproofing casing
Arrangement of reinforced concrete external and internal walls
Construction of reinforced concrete columns
Construction of reinforced concrete walls, partitions, ventilation ducts
Erection of reinforced concrete beams, chords, lintels, slabs and roofs, structures in horizontal sliding formwork
Laying concrete mixture in blocks of reinforced concrete structures of hydraulic structures
Reinforcement of building structures with reinforced concrete embeddings, clips and concrete blocks
Strengthening and replacement of reinforced concrete pavements
15. Works on the installation of prefabricated reinforced concrete and concrete structures
Installation of blocks of external and internal walls of buildings
Installation of concrete ladders
Bank fastening with concrete massifs
Production and installation of concrete masses with transportation
Installation of permanent supports made of concrete blocks and stones
Installation of retaining walls, caps, rack supports made of concrete blocks
Installation of reinforced concrete foundations for columns, frames, supports
Installation of reinforced concrete columns, capitals, frames, racks and rods
Jumper setting
Installation of roof beams and trusses
Installation of wall panels for exterior and interior walls
Installation of volumetric blocks of residential buildings
Installation of plates of loggias, balconies, peaks, cornice plates, sanitary pallets
Installation of small reinforced concrete structures (parapets, drains, window sills)
Installation of flights of stairs and landings
Installation of elevator shafts and volumetric elements of bins
Installation of partition panels, screens, dividing walls, stiffening diaphragms, ventilation units
Installation of sanitary cabins
Installation of blocks from armored panels, ballast and slot structures
Installation of wall panels for drain wells, walking yards, silos, mills, bunkers at thermal power plants
Installation of wall panels in the construction of linear buildings
Installation of floor slabs and coverings for TPP stairs, bridges, pipes, platforms, linear buildings
Installation of prefabricated reinforced concrete platforms, crossbars, consoles, superstructures from floating facilities
Installation of frame and formwork slabs, shells, parapets of mooring embankments and piers
Installation of supports, trays, boxes, blocks, gratings when arranging channels and feeders in agricultural buildings
Installation of foundation structures, retaining walls, heads, bed supports during the construction of bridges, pipes of power transmission lines and hydraulic structures
Installation of span structures of bridges from precast concrete structures from the shore
Construction of tunnels in an open way from precast concrete structures
Device for lining trunks and tunnels from prefabricated reinforced concrete tubing, panels and blocks
Arrangement of stairs and porches with entrance platforms
Laying beams and crossbars
Laying of panels, shells and floor slabs and coverings of one-story and multi-story buildings
Laying of reinforced concrete culvert pipes under embankments and collectors for laying communications
Laying and replacement of steps laid on stringers or a solid base
Laying and coating of railway slabs of tram tracks
Installation of columns, racks, masts, beams and crossbars of thermal power plants, open and closed switchgears
Fastening of the bottom and slopes with reinforced concrete slabs with thrust bars
Shore fixing with tetrapods and massifs
Covering roads and roadsides with precast concrete slabs
Installation of garbage chutes from asbestos-cement pipes with a diameter of 400 mm with inlet valves
16. Works on the installation of metal structures
Installation of frame structures of buildings and structures
Installation of structures of cooling towers, tanks, ventilation and chimneys, coke plants, pipelines, galleries
Installation of dryer structures, casings, screens, chambers, hearths, beams, frames, frames, grates and other structures of furnaces, pipes, dried electrolyzers
Installation of structures of prefabricated buildings from three-layer aluminum panels
Installation of cabin structures from three-layer aluminum panels for radio relay lines and metal heat chambers
Installation of overhead and crane runway structures
Installation of light tubular roof structures
Installation of structures for gates, stairs, platforms, doors, hatches, manholes
Installation of open structures, switchgears, searchlight masts, antenna systems, waveguide bridges with supports
Installation of window blocks, stained-glass windows, partitions (made of aluminum alloys, steel and others)
Construction of buildings from blockboxes
Installation of superstructures from steel structures with assembly and transport
Installation of mooring bollards
Installation of metal railings for stairs
Installation of gates, gratings, gates, pipelines, bridges, mooring devices and other metal structures of hydraulic structures
Installation of steel fasteners and roller bearings
Installation of keil - fenders and a support ring in trunks fixed with cast-iron tubing
Arrangement of suspended ceiling structures and soundproof walls
Arrangement and development of permanent and temporary metal supports in mine shafts and tunnels
Corrugated steel decking for underground channels
Suspended ceiling sheathing and cooling tower cladding with aluminum alloy sheets
Sheathing of walls and roofing with profiled iron or prefabricated panels
Fastening of building structures with building clips, bolts, rings
Extension of cast-iron tubing and installation of a picket ring
17. Works on the installation of wooden structures
Installation of wooden structures, frames, rafters, chairs
Gate installation
Installation of beams, arches, trusses and panels
Installation of visors, backlash - closets, fire boxes, tables
Installation of rows, arrangement and development of stocks
Installation of conductors, ladder ladders, running boards, barriers
Construction of wooden structures of bridges, flyovers, wheel ducts, hydraulic structures
Arrangement of walls from wooden structures and parts
Wooden bridge construction
Assembly of coverings and ceilings
18. Work on the installation of light enclosing structures
Installation of wood concrete and asbestos-cement slabs and wall panels, coatings
Installation of walls, ceilings, partitions and umbrellas from asbestos-cement sheets according to the finished frame
Installation of sprinkler blocks from asbestos-cement sheets
19. Works on the installation of walls from panels of the "SANDWICH" type and sheet assembly
20. Works on the device of stone structures
Installation of circles and formwork for laying arches, vaults and walls of industrial furnaces
Installation and dismantling of inventory external and internal scaffolding
Jumper setting
Laying of foundations, basement walls, retaining walls, laying of workings with rubble stone
Ceramic wall masonry
Laying structures made of limestone products with facing bricks
Brick laying of channels, pits, furnaces, hearths, chimneys with grooves
masonry brick pillars, arches, arbors, porticos and other structures made of ordinary brick
Brickwork of walls made of ordinary clay and silicate bricks with ceramic brick cladding
Brick masonry walls and ceramic tile cladding
The device of partitions made of bricks and ceramic stones
Construction of structures from tufa and diabase blocks
The device of partitions from piece gypsum and lightweight concrete slabs
21. Works on shielding rooms and arrangement of deformation
Screening of floors, walls, doors, ceilings with copper or steel sheets and mesh
Sheathing of walls and roofing of workings with sheet steel
Installation of protective steel meshes
Upholstery of walls, ceilings and doors with roofing steel on felt with asbestos lining
Sealing of horizontal and vertical joints and seams between panels, windows, doors
Chasing seams of lining from tubings and seams between columns and girders
Construction of expansion and anti-seismic joints
22. Works on the device and lining of industrial furnaces and flue
Installation of circles and formwork for laying arches, vaults and walls of industrial furnaces
Laying and lining of industrial pipes
Bricking surfaces with heat-resistant and refractory concrete, slabs, refractory mass
Lining of reinforced concrete industrial pipes with acid-resistant bricks
Masonry, lining and lining of furnaces and pipes with refractory products and bricks
Laying of nozzles, stuffing the hearth with coal mass, installation of anode and hearth blocks
23. Roofing works
Asbestos cement roofing
Tiled roofing with sheathing
Roll roofing device
Roofing made of bituminous mastic with fiberglass or fiberglass lining
The device of shallow roofing and lining on the facades of roofing iron
Installation of gutters with overhangs and roof railings
Priming of bases and vapor barrier device
24. Works on waterproofing building structures
Injection of mortar behind the lining of tunnels and mine shafts
Cement screeding, gunning, grouting and ironing
Device for horizontal and lateral waterproofing with cement and liquid glass
Clay lateral coating waterproofing device
Device for lateral coating waterproofing of concrete and ceramic structures
The device of plaster waterproofing with cast asphalt or mastics, resin, varnish
Waterproofing device
The device of a continuous screen curtain made of hydrorelin and polyethylene film
Device for insulating steel pipelines with bitumen-rubber mastic
Insulation device for steel pipelines with bitumen-polymer mastic
Overlapping and pasting joints in hydraulic structures with hydrorelin
Coating of concrete and reinforced concrete pipes with bituminous mastic
25. Works on anti-corrosion protection of building structures and
equipment
Masonry made of acid-resistant brick, stone, andesite
Floor covering and lining of surfaces with acid-resistant bricks
Surface lining with carbon and graphite blocks
Lining of surfaces with acid-resistant plates
Coating and pasting of equipment surfaces with rubber, plastics, sealants, roll materials
Pasting of surfaces with sheet asbestos
Electrometallization of surfaces with zinc, aluminum, nichrome and stainless steel wire
Impregnation of crushed stone with mastic "BITUMINOL N-2"
Hydrophobization and surface fluting
Painting surfaces with varnishes, paints, enamels
Fire protection of wooden structures
Fire protection of roof battens and truss decking
Antiseptic treatment of wooden structures of buildings
26. Works on thermal insulation of building structures, pipelines
and equipment
Insulation of coatings with monolithic cellular concrete
Insulation of hot surfaces with piece and prefabricated thermal insulation products
Insulation of hot surfaces with wrapping materials and packing of heat-insulating fibrous materials
Insulation of hot surfaces with mastics and asbestos-perlite by spraying
Insulation of furnace masonry, boiler surfaces and pipelines with asbestos
Coating the surface of pipeline insulation with asbestos-cement casings, glass cement, fiberglass, fiberglass
Covering the surface of pipeline insulation with sheet metal or corrugated aluminum sheets
Surface coating of pipeline insulation, wrapping and pasting the insulation with films, fabrics, roll materials
27. Works on the arrangement of internal engineering systems and equipment
Installation of valves, dampers, hermetic doors and hatches
Installation of distribution boxes, equipment exhausts, brackets, stands and vibration-isolating bases
Installation of valves, gate valves, non-return valves, taps and mixers on internal networks
Installation of water meter units
Installation of water heaters and boilers
Installation of compensators
Installation of elevator nodes
Installation of gas stoves
Installation of pressure and reduction regulators
Installation of heaters and air heaters
Installation of fans and ventilation units
Installation of chambers for supply irrigation, maintenance, leveling, recirculation
Installation of heating water and steam boilers
Installation of heating cast-iron sectional steam boilers
Laying electrical wiring in apartments residential buildings
Laying distribution networks in basements, attics, stairwells
Installation of risers in finished channels on floors with the installation of shields
Installation of lighting boards
Installation of electric stoves
Installation of a lightning rod, cable platform, hatches, steps, a checkpoint on the supports and roofs of buildings
Installation of valves
Installation of insulators
Installation of grounding switches
28. Works on installation of outdoor engineering networks and communications
Installation of water, sewer and drain wells
The device of telephone wells and boxes with the device of inserts, installation of hatches and brackets
Installation of water wells, caps, catchment damper
Construction of foundations and gravel and crushed stone platforms for gate valves and cranes
The device of drainage funnels and trays in the suction of embankments
Arrangement of manure removal channels, cable troughs and trays
Laying precast concrete gutters
Reinforcement of the platform behind the absorber spurs with precast concrete slabs
Arrangement of wooden base and anchors for radio masts
Concrete and reinforced concrete base and anchors for radio masts
The device of complexes of bases and anchors for masts
The device of block or pile foundations for steel supports of the contact network
Installation of supports for power lines 35-750 kV of feeder lines and wooden automatic blocking lines
Installation of supports for power transmission lines 35-750 kV of feeder lines and reinforced concrete automatic blocking lines
Installation of poles for power transmission lines 35-750 kV radio masts and steel radio towers
Installation of supports for power transmission lines 0.4-35 kV of the contact network and industrial electric transport, communication lines and wooden radio
Installation of supports for power lines 0.4-35 kV of the contact network and industrial electric transport, communication lines and radio communication reinforced concrete
Installation of feeder line supports from asbestos-cement pipes
Installation of reinforced concrete slabs, crossbars and anchors with braces, attachments to the supports
Installation and fastening on supports of communication lines and radio broadcasting networks of wooden or steel traverses
Installation of guy wires and metal struts to supports
Installation of struts and wooden attachments to the supports
Installation of rigid crossbars, bridges and viewing cradles with crossbars
Installation of wooden radio masts
Installation of reinforced concrete radio masts
Installation of radio masts from asbestos-cement pipes
Installation of bases and supporting structures of packaged substations
Installation of steel poles of the contact network and industrial electric transport
Suspension of wires of power lines and contact lines
Suspension of lightning wires
Laying cables in underwater trenches
Installation on supports of overhead lines and switchgear structures of disconnectors, arresters, switches
Installation of a control - measuring column and cathode station
Installation of lightning protection parts for beam and loop grounding
Arrangement of sites for the installation of signal points on embankments with reinforcement with log cabins and reinforced concrete slabs
Grounding device for wooden poles and a typical ground loop
Laying pipelines from reinforced concrete pressure pipes
Laying pipelines from asbestos-cement pressure pipes
Laying pipelines from cast iron pressure pipes
Laying pipelines from steel pipes with the installation of hydraulic gates, bypasses, candles
Channelless laying of steel pipelines with anti-corrosion, armored concrete and bitumen-pearlite insulation
Laying channelless pipelines from polyethylene pipes
Inserting fittings and tees into existing networks, shutting off and plugging gas pipelines
Testing of pipelines for strength and tightness with flushing and installation of glands
Suspension of underground utilities at their intersection with the highway
Laying pipelines from plastic pipes
Laying pipelines from cast iron sewer pipes
Laying pipelines from cast iron pressure pipes
Laying pipelines from steel pipes
Testing hydraulic and pneumatic pipelines
Installation of safety, receiving, reducing valves
Installation of gate valves and check valves on external networks of water supply, heating, gas supply
Assembly and installation of gate valves and linear valves
Installation of water meter units
Installation of fire hydrants, water columns, traveling cranes, air vents
Installation of tanks and condensate collectors
Installation of high-speed and capacitive water heaters
Installation of steam and water distribution combs from steel pipes
Installation of mud collectors and filters
Installation of compensators
Installation of air collectors from steel pipes and air vents and hydraulic seals
Installation of elevator nodes
Installation of pointing devices (pressure gauges, thermometers, level indicators, air valves)
Installation of gas burners
Installation of filters, scrubbers, cyclones
Installation of centrifugal pumps with piping
Installation of drainage and spillway funnels
Laying cables fixed on a cable or staples
Tightening and routing wires
Installation of input - switchgear
Installation of step-down transformers
Suspension for fastening feeders on intermediate, corner and anchor bases
Suspension of wires on pole and rack communication and radio lines
Laying of pipelines from steel pipes, with welding of joints and installation of bends
Laying of pipelines from steel pipes with flanges and welded joints from finished units and parts
Laying pipelines from steel pipes in shafts of mines, dewatering plants, in hydraulic lifting chambers, pulp pumping stations
Laying of pipelines from aluminum pipes
Laying pipelines from sheet aluminum
Laying of pipelines from copper, brass pipes
Laying pipelines from cast iron flanged pipes
Laying pipelines from lead pipes
Laying of pipelines from sheet lead
Laying pipelines from glass pipes
Laying pipelines from plastic pipes
Installation when laying pipelines of filters, water and oil separators, compensators, bypass devices
Installation of valves
Installation of embedded and selected devices of automation systems, fire extinguishing installations, equipment for grease lubrication systems
Filling containers with foam concentrate
Tapping and connection of pipelines to existing pipelines
29. Installation of technological equipment
Installation of equipment for thermal power plants
Installation of heat power equipment
Installation of elements of steam, hot water boilers
Installation of installations for water treatment and water treatment
Installation of steam turbine and gas turbine units
Installation of stationary diesel engines and diesel generators
Installation of equipment for nuclear power plants
Installation of equipment for hydroelectric stations and hydraulic structures
Installation of hydraulic turbines
Installation of generators for hydroelectric power plants
Installation of oil pressure units
Installation of other hydraulic engineering equipment
Installation of metal structures of spiral chambers and lining of hydraulic turbines
Installation of mechanisms for lifting, traction cleaning, gates and sluice gates
Installation of equipment for coal and peat industries
Installation of equipment for the mechanization of preparatory and cleaning works and mining
Installation of underground transport equipment
Installation of equipment for open pit mining
Installation of peat equipment
Installation of crushing and grinding enrichment and sintering equipment
Installation of crushing and grinding equipment
Installation of equipment for sorting and enrichment
Installation of sintering equipment
Installation of equipment for enterprises of the chemical and oil refining industries
Installation of equipment for enterprises producing nitrogen, ammonia, acids, salts, mineral fertilizers
Installation of equipment for industrial enterprises
synthetic rubber and synthetic alcohol
Installation of equipment for enterprises in the industry of plastics, chemical fibers
Installation of equipment for the enterprises of the paint and varnish industry
Installation of equipment for enterprises of the mining and chemical industry, automatic fire extinguishing
Installation of equipment for oxygen industry enterprises
Installation of equipment for the wood chemical industry
Installation of equipment for ferrous metallurgy enterprises
Installation of equipment for coke production of the main
Installation of equipment for blast-furnace production of the main
Installation of steelmaking equipment
Installation of continuous casting machines, testing, rope, wire, unwinding and winding machines
Installation of hardware production equipment for the main
Installation of pipe foundry equipment
Installation of ferroalloy production equipment
Installation of auxiliary equipment for coke, blast furnace, hardware production (gates, valves, couplings, gates)
Installation of universal tensile machines
Installation of equipment for non-ferrous metallurgy enterprises
Installation of general purpose equipment
Installation of equipment for the extraction of non-ferrous metals
Installation of equipment for magnesium workshops
Installation of equipment for processing non-ferrous metals
Installation of equipment for rolling mills
Installation of rolling machines
Installation of pipe rolling and pipe welding equipment
Installation of stations and systems for thick and liquid lubricants, oil cleaning machines
Mounting of fluid friction bearings
Installation of metalworking equipment
Installation of metal-cutting machines
Installation of automatic lines for metalworking
Press installation
Installation of foundry equipment
Installation of woodworking equipment
Installation of sawmill equipment
Installation of equipment for woodworking and plywood production
Installation of gluing and assembly equipment
Installation of equipment for the production of matches
Installation of equipment for cooperage and container production
Installation of equipment for the production of window and door blocks and furniture finishing
Installation of lifting and transport equipment
Installation of cranes
Installation of conveyors, belt, trolley, roller tables, conveyors, bucket elevators, elevators
Installation of hoisting and transport equipment units
Shelving installation
Installation of chains, transition sections, ropes
Installation of equipment for cable cars with tests
Installation of safety mesh fences
Installation of elevators, lifting platforms, flat-cup lifts, shaft cages, loading and unloading devices
Installation of winches and lifting and traction machines
Installation of equipment for narrow-gauge railway transport
Installation of technological metal structures
Installation of beds, frames, tracks, drives
Installation of ropes of cable cars
Installation of supporting metal structures
Installation of gates, sluice gates of hydraulic structures
Installation of supports, racks, clamps, frames, embedded elements for equipment
Installation of gutters, ducts, cable blocks, embedded structures from rolled profiles
Installation of technological metal structures in blast-furnace, steel-smelting production and in mine faces
Installation of pneumatic conveying pipelines from sheet steel
Installation of technological pipelines
Laying of pipelines from steel pipes, with welding of joints and installation of bends
Laying of pipelines from steel pipes with flanges and welded joints from finished units and parts
Laying pipelines from water and gas pipes, ammonia and brine batteries, grease lubrication systems, automation systems
Laying pipelines from steel pipes in mine shafts,
dewatering plants, in hydraulic lifting chambers, pulp pumping stations
Laying of pipelines from aluminum pipes
Laying pipelines from sheet aluminum
Laying of pipelines from copper, brass pipes
Laying pipelines from cast iron flanged pipes
Laying pipelines from lead pipes
Laying of pipelines from sheet lead
Laying of pipelines from ceramic and porcelain pipes
Laying pipelines from glass pipes
Laying pipelines from plastic pipes
Installation when laying pipelines of filters, water and oil separators, compensators, bypass devices
Installation of valves
Installation of embedded and selected devices of automation systems, fire extinguishing installations, equipment for grease lubrication systems
Filling containers with foam concentrate
Tapping and connection of pipelines to existing pipelines
Installation of equipment for enterprises in the building materials industry
Installation of mixing and dispensing equipment
Installation of equipment for the production of cement, lightweight aggregates
Installation of equipment for the production of glass, high-quality glassware and fiberglass
Installation of equipment for the production of asbestos-cement products
Installation of equipment for the production of bricks, tiles, ceramic products, cinder blocks and slag granulation
Installation of equipment for the production of gypsum and gypsum products
Installation of equipment for the extraction and processing of facing stone
Installation of equipment for the production of heating sanitary - technical devices
Installation of equipment for production reinforced concrete products and cellular concrete products
Installation of equipment for the manufacture of frames from reinforcing steel
Installation of lime production equipment
Installation of equipment for the production of reed products, chipboards
Installation of equipment for mica processing and asbestos production
Installation of equipment for pulp and paper industry enterprises
Installation of equipment for the preparation of wood raw materials for processing, for the production of pulp and semi-cellulose
Installation of equipment for the production of paper, cardboard, market pulp and market wood pulp
Installation of equipment for processing paper and cardboard into products, for cutting, sorting, packaging and transporting paper, cardboard and pulp
Installation of equipment for printing industry enterprises
Installation of equipment for the production of text and stereotype forms
Installation of equipment for printing, copiers
Installation of equipment for stitching and binding, for the manufacture and finishing of cardboard and white products, cardboard production
Installation of equipment for agricultural production
Installation of milk collection and storage equipment
Installation of water-lifting equipment, water heaters and drinkers
Installation of feed preparation equipment
Installation of stall equipment for cattle and machine tools for sows
Installation of lifting and transport equipment
Installation of equipment for rearing and keeping poultry
Installation of equipment for shearing station and rabbit farms
Installation of equipment for feeders and conveyors - feed distributors
Installation of manure equipment
Installation of equipment for granaries and grain processing enterprises
Installation of equipment for drying and cleaning grain
Installation of equipment for the production of flour and corn
Installation of equipment for the production of animal feed
Installation of dosing, mixing, sewing equipment
Installation of transport and distribution equipment
Installation of loading and unloading equipment
Installation of other equipment
Installation of equipment for microbiological industry enterprises
Installation of equipment for light industry enterprises
Installation of equipment for leather manufacturing enterprises
Installation of equipment for the tanning and extract industry
Installation of footwear industry equipment
Installation of equipment for the production of auxiliary parts
Installation of equipment for knitting, textile and haberdashery industry
Installation of equipment for the dyeing and finishing knitting industry
Installation of fur industry equipment
Installation of equipment for sewing, wet - heat treatment
Installation of equipment for saddlery and saddlery production, leather and haberdashery industry
Installation of equipment for the bristle-brush industry
Installation of equipment for the felt industry
Installation of equipment for the processing of secondary raw materials
Installation of drying and disinfection equipment
Installation of flooring and ironing tables
Installation of equipment for the knitting industry
Installation of equipment for textile industry enterprises
Installation of equipment for weaving production
Installation of machines for roving, spinning, twisting, jute-kenaf production
Installation of equipment for finishing textile production
Installation of equipment for cotton ginning plants and processing cocoon raw materials
Installation of equipment for food industry enterprises
Installation of equipment for the baking industry
Installation of sugar industry equipment
Installation of equipment for the meat and poultry processing industry
Installation of equipment for fish industry enterprises
Installation of equipment for dairy industry enterprises
Installation of equipment for oil and fat industry enterprises
Installation of equipment for enterprises of the canning, poultry-concentrate and vegetable-drying industries
Installation of equipment for pasta and confectionery enterprises
Installation of equipment for enterprises of the yeast, starch-treacle, wine-making, non-alcoholic industries
Installation of equipment for tobacco and tea enterprises
Installation of equipment for trade and public catering establishments
Installation of equipment for the production of tin containers
Installation of weighing equipment
Installation of transport, platform, elevator scales
Installation of scales for bulk weighing bulk materials and dosing
Installation of scales used in the food industry
Installation of equipment for electrical industry enterprises
Installation of cable equipment
Installation of equipment for the manufacture of electrical machines
Installation of equipment for the production of chemical current sources
Installation of test equipment
Installation of equipment for painting products
Installation of equipment for the electroceramic industry and for the production of electrical insulating materials
Installation of equipment for the production of light sources
Installation of electrical installations
Installation of power transformers and substation sets
Installation of oil coolers and heat exchangers
Installation of reactors and capacitors
Installation of short-circuiters, disconnectors, switches, arresters for voltage up to 750 kV
Installation of current and voltage transformers, step-down transformers, autotransformers
Installation of electrical machines and units with the installation of current collectors
Installation of circuit breakers, switches, air circuit breakers, plug-in devices
Installation of switchboards and lighting, terminal boxes and taps
Installation of single-row and double-row shields
Installation of cabinets, consoles, racks and input and distribution devices
Installation of ballast and guide equipment
Installation of accumulators, alkaline batteries with charging
Installation of electric heaters
Installation of electrical appliances
Installation of insulators
Installation of busbar bridges, flexible busbars and sectioning points
Installation of equipment for urban electrified transport networks
Installation of asbestos-cement slabs, walk-through and dividing boards
Installation of grounding switches
Installation of fixtures
Laying of bus ducts, trolls, current ducts, rails of ground loops
Laying of busbars of interhull and main busbars
Laying of contact networks of industrial, railway and urban transport
Laying outdoor lighting networks
Laying of cable networks with the device of couplings and cutting ends
Laying internal wiring
Pouring electrical equipment with transformer oil and drying it
Covering the cable with bricks or slabs with a bed
Rope signaling device in mines
Transportation of equipment during the electrification of railways
Installation of compressor machines, pumps and fans
Installation of compressor units and piston, centrifugal expanders
Installation of ventilation equipment
Installation of pumping units for general purposes
Installation of electric ovens
Installation of auxiliary installations
Installation of equipment of enterprises for the repair of household machines and appliances
Installation of machines and installations for washing, ironing and storing linen
Installation of machines and installations for dry cleaning and dyeing of clothes and carpets
Installation of machines and installations for enterprises for the repair of household machines and appliances
Installation of equipment for gas purification
Installation of equipment for electrical and mechanical gas cleaning
Performing related work during the installation of electrostatic precipitators
Installation of equipment for electronic industry enterprises and communication facilities
Installation of vacuum equipment
Installation of thermal equipment
Installation of welding equipment
Installation of machining equipment
Installation of equipment for glass and ceramic production
Installation of chemical process equipment
Installation of equipment for assembly, general purpose and testing
Installation of optical and precision mechanics equipment
Installation of equipment for enterprises in the communications industry
Installation of signaling, centralization and blocking equipment in railway transport
Installation of equipment for the electric wand system and route control devices, mechanical interlocking and semi-automatic blocking
Installation of control room equipment, electrical interlocking and blocking
Installation of equipment for mechanization, automation of sorting humps and pneumatic mail
Installation of equipment for power supply and cable devices
Installation of communication equipment
Installation of telephone exchanges and switches of the Central Bank, MB, dispatching, intercity and office communications
Installation of telephone exchanges and switches of the MB system for director, dispatch and office communications and telephone quasi-telephone exchanges
Installation of rural telephone exchanges with verification and adjustment
Installation of tripod frames with fencing devices, lighting and signaling
Installation of telephone exchange equipment, including high-frequency communication equipment
Installation of radio stations
Installation of radio bureau equipment, radio stations, radio broadcasting nodes
Installation of antenna devices with related work and configuration
Installation of equipment for radio and television centers
Installation of subway and tunnel equipment
Installation of escalators
Installation of ventilation valves
Installation of communication equipment for mines and railway transport
Installation of equipment for electrical alarm, fire, call and remote signaling with blocking of surfaces
Mounting of stands for water cooling of transmitters
Installation of doors with electrical and mechanical interlock contact
Installation of postal mechanization equipment
Installation of fences
Laying cables for communication lines and station
Laying of wires station, waveguide
Laying feeder lines and waveguides
Installation of transformers and feeder loops, systems for keeping the waveguide under excess pressure
Connection of existing cables with their relocation without interruption of subscribers
Pulling the cable out of the sewer
Installation of devices, means of automation and computer technology
Installation of appliances
Installation of indicators, sensors, signaling devices of various parameters
Installation of equipment for operational control and management, collection and transmission of initial information
Installation of actuators and regulators
Installation of panels, shields, tripods, consoles
Arrangement of pipe and pneumatic cable wiring with related work
Arrangement of electrical wiring on metal panels and in panels with related work
Mounting power supplies
Installation of laboratory equipment for checking instruments
Installation of equipment for specialized control systems and computer technology
Installation of equipment for healthcare institutions and medical industry enterprises
Installation of sterilization and pharmacy equipment
Installation of otolaryngological and dental equipment
Installation of equipment for physiotherapy rooms
Installation of X-ray room equipment
Installation of general surgical equipment, for anesthesia, artificial respiration and oxygen therapy
Installation of ophthalmic equipment
Installation of equipment for obstetric - gynecological and urological
Installation of equipment for diagnostic studies and laboratory
Installation of hospital, disinfection and disinfestation equipment
Installation of equipment for medical industry enterprises
Installation of equipment for theatrical and entertainment enterprises
Installation of stage equipment
Installation of counterweight plates
Hanging ropes
Installation of sound equipment for theatrical and entertainment enterprises
Installation of equipment for cinematography enterprises
30. Commissioning works
Commissioning works electrical devices
Commissioning of synchronous generators and excitation systems
Commissioning of power and instrument transformers
Commissioning of switching devices
Commissioning of relay protection devices
Commissioning of automation in power supply
Commissioning of voltage and control current systems
Commissioning of electrical machines and electric drives
Commissioning of automation systems, alarm systems and related devices
Commissioning works automated systems management
Commissioning of technical means of automated control systems
Commissioning of software for computer systems
Commissioning of stand-alone system commissioning
Commissioning works of complex adjustment of systems
Commissioning of telemechanics
Commissioning of ventilation and air conditioning systems
Adjustment of ventilation and air conditioning systems
Testing of ventilation and air conditioning systems
Commissioning of lifting and transport equipment
Commissioning of hoisting and transport mechanisms of discontinuous action
Commissioning of transport mechanisms of continuous action
Commissioning of metalworking equipment
Commissioning of automatic machine lines
Commissioning of multi-purpose metal-cutting machines with CNC
Commissioning of metal-cutting machines with CNC digital indication
Commissioning of unique metal-cutting machines weighing over 100 tons
Commissioning of other CNC machine tools
Commissioning of refrigeration and compressor units
Commissioning of refrigeration units
Commissioning of compressor units
Commissioning of thermal power equipment
Commissioning of steam boilers
Commissioning of hot water boilers
Commissioning of boiler auxiliary equipment
Commissioning of water treatment equipment and chemical water treatment equipment
Start-up and adjustment works of technological installations of the fuel economy
Commissioning of the gas-air path
Commissioning of general boiler systems and engineering communications
Commissioning of woodworking equipment
Commissioning of equipment for primary processing of timber and wood processing for technological raw materials
Commissioning of equipment for processing and finishing wood
Commissioning of drying plants
Commissioning of water supply and sewerage facilities
31. Road construction works
Construction of unpaved roads covered with sand, crushed stone or gravel
Arrangement of soil foundations, earthen and crushed stone coatings
The device of coverings from a cobble stone and a stone blocks
Concrete, mosaic, cement, metal-cement coatings
Installation of asphalt concrete and xylolite pavements
Installation of road frame metal and reinforced concrete structures
Installation of road parapet barriers on reinforced concrete columns
Manufacture and installation of wooden railings and fences
Road marking device
32. Works on the construction of railway tracks
Laying of normal gauge railway tracks by separate elements with post-settlement repairs and other related works
Laying of normal gauge railway tracks by tracklayers with preparation of links at the base and related work
Laying rails in one thread on the finished base
Laying turnouts and cross ramps on normal gauge tracks
Laying blind crossings on normal gauge tracks
Installation of temperature compensators
Laying a mounting frame with tracks on an underwater ballast base
Laying reinforced concrete beam lashes with tracks on an underwater ballast base
Laying of longitudinal and transverse rail tracks for transformer rolling
Laying of narrow gauge railway tracks with post-settlement repairs
Laying turnouts and cross ramps on narrow gauge tracks
Laying blind crossings on narrow gauge tracks
Turntable installation on narrow gauge tracks
Installation of joints on crushed stone ballast
Installation of turnouts on crushed stone ballast
Installation of track signal signs, benchmarks, end bends
Device for crossings over narrow-gauge tracks
Installation of crane runways on embankments and waterworks
Arrangement of crossings over railway tracks of normal gauge
Arrangement of rail or wooden stops
Movement of railway tracks at a distance of up to 2 m
Moving turnouts
Railroad ballasting
33. Underwater works (diving)
Lifting objects out of the water
Leveling and vibrocompaction under water of horizontal beds by divers
Moving stone under water, removing stone and gravel from water
Lowering metal and reinforced concrete shells of heads under water
Installation of mooring barrels on reinforced concrete anchors in the water area
34. Mining works
Mining works
Sinking of mine shafts, pits, workings
Sinking of mine shafts in a thixotropic jacket
Sinking of tunnels, furnels, chambers, adits with the device of permanent and temporary crossings
Sinking of split furnaces, clearings, pits, chambers and expansion of horizontal and inclined workings
Reception and unloading of soil during the passage of mine shafts, galleries, tunnels
Entry into the face and withdrawal from the face of the tunneling shield
Device for fastening mine shafts and tunnels with inventory rods and spacers
Installation of shale and water barriers
The device of temporary supports and installation of arches of fastening
Arrangement and disassembly of the reinforcement of mine shafts
Installation and disassembly of wooden fasteners - frames, executions, ties, skins
Fastening and sheathing of walls and roofs, pits, workings, stair compartments with boards, logs and mine racks
35. Well construction works
Well construction works
Construction and installation of oil and gas wells
Drilling oil and gas wells with testing them for productivity
Installation of filter casing or freezing pipes and devices
Installing a filter on a riser pipe
Annular space cementation and shoe plugging
Fixing wells with pipes
Fixing the well with reinforced concrete rings
Filter head and water pumping devices
Transportation of well equipment
Drilling of relief wells
Repair work, as a rule, depending on the frequency of carrying out, is divided into two types: current repairs and overhaul.
Lists of types of work on capital repairs are contained in departmental acts (Regulations, Norms and Rules .., Instructions, Recommendations, etc. ..). These lists of types of work vary depending on the type of capital construction object, its purpose.
Types of work are given in annexes to departmental regulations, the texts of which are given in the attachment to this publication:
Appendix 8. List of works on the overhaul of buildings and structures ( Decree of the Gosstroy of the USSR of December 29, 1973 N 279 "On approval of the Regulations on the scheduled preventive maintenance of industrial buildings and structures" (together with "MDS 13-14.2000 ..."))
Appendix N 8. An approximate list of works performed during the overhaul of the housing stock ( Decree of the Gosstroy of the Russian Federation of September 27, 2003 N 170 "On approval of the Rules and norms for the technical operation of the housing stock")
Annex 9. List of works on major repairs of buildings and structures ( Order of the Ministry of Justice of Russia dated September 28, 2001 N 276 (as amended on January 24, 2006) "On approval of the instructions for the technical operation of buildings and structures of institutions of the penitentiary system")
Table 2.3. The list of works on the overhaul of apartment buildings to be included in the scope of works financed from the funds provided for by Federal Law N 185-FZ ( )
Overhaul- repairs carried out to restore technical and economic characteristics object to values close to the design ones, with the replacement or restoration of any constituent parts (Order of the Gosstroy of the Russian Federation of December 13, 2000 N 285 "On approval of the Standard Instructions for the Technical Operation of Heat Networks of Public Heat Supply Systems").
Overhaul- carrying out a complex of construction works and organizational and technical measures to eliminate physical and moral deterioration, not related to changes in the main technical economic indicators building and functional purpose, providing for the restoration of its resource with partial replacement, if necessary, of structural elements and systems of engineering equipment, as well as improving operational performance ( Decree of the Government of Moscow of July 30, 2002 N 586-PP (as amended on December 23, 2015) "On approval of the Regulations on the unified procedure for pre-project and project preparation construction of engineering communications, structures and objects of road transport support in the city of Moscow").
Capital repairs of capital construction facilities(with the exception of linear facilities) - replacement and (or) restoration of building structures of capital construction objects or elements of such structures, with the exception of load-bearing building structures, replacement and (or) restoration of engineering and technical support systems and networks of engineering and technical support of capital construction objects or their elements, as well as the replacement of individual elements of load-bearing building structures with similar or other elements that improve the performance of such structures and (or) the restoration of these elements ( (as amended on 06/18/2017)
For the overhaul of buildings and structures include works on the restoration or replacement of individual parts of buildings (structures) or entire structures, parts and engineering equipment due to their physical wear and tear and destruction with more durable and economical ones that improve their performance ( Decree of the Gosstroy of Russia dated 03/05/2004 N 15/1 (as amended on 06/16/2014) "On approval and implementation of the Methodology for determining the cost construction products on the territory of the Russian Federation" (together with "MDS 81-35.2004...")).
Building overhaul- a set of construction and organizational and technical measures to eliminate physical and functional (moral) wear and tear that do not involve changes in the main technical and economic indicators of a building or structure, including, if necessary, the replacement of individual or all structural elements (except for non-replaceable) and engineering systems equipment with their modernization. Capital repairs do not extend the service life of buildings, as it is determined by the most durable elements that are not replaced during repairs ( "Methodological recommendations for the formation of the scope of works for the overhaul of apartment buildings financed from the funds provided for by the Federal Law of July 21, 2007 N 185-FZ "On the Fund for Assistance to the Reform of the Housing and Communal Services" (approved by the State Corporation "Fund for Assistance to the Reform of Housing and Utilities" 15.02.2013)
Capital repairs of an apartment building- carrying out and (or) rendering of the works and (or) services provided for by this Federal Law to eliminate malfunctions of worn structural elements common property owners of premises in apartment building(hereinafter referred to as common property in an apartment building), including their restoration or replacement, in order to improve the operational characteristics of common property in an apartment building ( article 2 of the Federal Law of July 21, 2007 N 185-FZ (as amended on June 23, 2016) "On the Fund for Assistance to the Reform of Housing and Communal Services").
Capital repairs of the common property of an apartment building: a set of works (services) for the replacement and (or) restoration (repair) of the bearing and (or) functional capacity of structures, parts, engineering and technical support systems that have lost during operation, individual elements of the supporting structures of an apartment building for similar or other improving indicators up to their normative state, when the volume of such work exceeds the current repair ( )
Overhaul is divided into complex overhaul and selective.
a) is a repair with the replacement of structural elements and engineering equipment and their modernization. It includes work covering the entire building as a whole or its individual sections, in which their physical and functional wear is compensated.
b) is a repair with full or partial replacement of individual structural elements of buildings and structures or equipment, aimed at full refund their physical and partially functional wear.
Classification as a major overhaul depends on technical condition buildings scheduled for repair, as well as the quality of their layout and the degree of internal improvement ( "Methodological recommendations for the formation of the scope of works for the overhaul of apartment buildings financed from the funds provided for by the Federal Law of July 21, 2007 N 185-FZ "On the Fund for Assistance to the Reform of the Housing and Communal Services" (approved by the State Corporation "Fund for Assistance to the Reform of Housing and Utilities" 15.02.2013))
Complete overhaul: replacement, restoration and (or) repair of the common property of an apartment building or its individual parts, carried out in relation to the majority of the common property of an apartment building ( "GOST R 51929-2014. National standard of the Russian Federation. Services of housing and communal services and management of apartment buildings. Terms and definitions" (approved and put into effect by Order of Rosstandart dated 11.06.2014 N 543-st)
Complex overhaul- covers all elements of the building, provides for the simultaneous restoration of all worn-out structural elements, engineering equipment and an increase in the degree of improvement of the building as a whole, eliminates physical and moral deterioration. Carrying out the next comprehensive overhaul of a building or structure is not advisable in cases where it is planned to demolish or transfer buildings or structures in connection with the upcoming construction on the site of another building or structure occupied by them, the reconstruction of the building is expected, the dismantling of the building is planned due to general dilapidation. In these cases, work must be carried out to maintain the structures of the building or structure in a condition that ensures their normal operation during the appropriate period (before demolition or reconstruction) ( )
Overhaul selective: replacement (restoration) of the common property of an apartment building or its individual parts, carried out in relation to a smaller part (some parts) of the common property of an apartment building ( "GOST R 51929-2014. National standard of the Russian Federation. Services of housing and communal services and management of apartment buildings. Terms and definitions" (approved and put into effect by Order of Rosstandart dated 11.06.2014 N 543-st)
Selective overhaul- covers individual structural elements of the building or its engineering equipment, while eliminating the physical wear and tear of individual elements and technical systems of the building. Selective overhaul is carried out in cases where a comprehensive overhaul of a building can cause serious interference in the operation of the facility, with significant wear of individual structures that threaten the safety of other parts of the building, if it is not economically feasible to carry out a comprehensive overhaul according to the restrictions given in the definition of a comprehensive overhaul ( Decree of the Government of Moscow dated September 29, 2010 N 849-PP (as amended on July 7, 2015) "On approval of the Regulations for the overhaul of real estate objects located in state property of the city of Moscow and transferred to trust management")
Emergency overhaul- repair or replacement of all structural elements, devices, systems of engineering equipment that have failed due to accidents, natural disasters, terrorist attacks and vandalism ( Decree of the Government of Moscow dated September 29, 2010 N 849-PP (as amended on July 7, 2015) "On approval of the Regulations for the overhaul of real estate objects owned by the city of Moscow and transferred to trust management")
For the overhaul of external engineering communications and improvement facilities include repair of water supply networks, sewerage, heat and gas supply and electricity supply, landscaping of courtyard areas, repair of paths, driveways and sidewalks, etc. ( Decree of the Gosstroy of Russia dated 03/05/2004 N 15/1 (as amended on 06/16/2014) "On approval and implementation of the Methodology for determining the cost of construction products on the territory of the Russian Federation" (together with "MDS 81-35.2004 ...")
Capital repairs of the highway- a set of works for the replacement and (or) restoration of the structural elements of the highway, road structures and (or) their parts, the implementation of which is carried out within the established permissible values and technical characteristics of the class and category of the highway and the implementation of which affects the design and other reliability characteristics and safety of the motor road and the boundaries of the right of way of the motor road are not changed ( Art. 3 of the Federal Law of November 8, 2007 N 257-FZ (as amended on February 7, 2017) "On highways and road activities in the Russian Federation and on amendments to certain legislative acts of the Russian Federation")
Capital repairs of the road surface- a complex of works in which a complete restoration and increase in working capacity is carried out pavement and pavement, subgrade and road structures, worn-out structures and parts are replaced or replaced with the most durable and durable ones, the geometric parameters of the road are increased, taking into account the increase in traffic intensity and axial loads of vehicles within the limits corresponding to the category established for the road being repaired, without increasing the width of the subgrade along the main length of the road ( Order of the Ministry of Housing and Public Utilities of the Moscow Region of June 29, 2015 N 125-RV "On approval of the Rules for the improvement of the territory of the urban district of Balashikha, Moscow Region")
The timing of the overhaul is either established by the parties, or established by regulatory legal acts(NPA). In the absence of an indication of the timing of the repair in the contract or normative act, it is carried out within a reasonable time.
The concept of "reasonable time" is traditional for civil law and is mentioned repeatedly in the norms of the Civil Code of the Russian Federation (see Article 314 of the Civil Code of the Russian Federation, in relation to pledge relations - clause 4 of Article 345, clause 1 of Article 358 of the Civil Code of the Russian Federation).
A reasonable period for carrying out a major overhaul depends on the condition of the property, its properties, climate characteristics, features of the major overhaul, technical capabilities and other reasons.
In addition, the regulatory legal acts can provide for both specific terms for the repair, and the procedure for determining them can be fixed, and the frequency of performing certain types of repair work can be established.
; Annex 8 to the Decree of the USSR Gosstroy of December 29, 1973 N 279 "On approval of the Regulations on the scheduled preventive maintenance of industrial buildings and structures" (together with "MDS 13-14.2000 ...")
Appendix 8
A. BY BUILDINGS
I. Foundations
1. Changing wooden chairs or replacing them with stone or concrete pillars.
2. Partial re-laying (up to 10%), as well as strengthening of stone foundations and basement walls, not related to the building superstructure or additional loads from newly installed equipment.
3. Restoration of vertical and horizontal insulation of foundations.
4. Restoration of the existing blind area around the building (more than 20% of the total blind area).
5. Repair of existing drains around the building.
6. Change of single collapsing stone and concrete pillars.
II. Walls and columns
1. Sealing cracks in brick or stone walls with clearing furrows, with bandaging of seams with old masonry.
2. Installation and repair of structures that reinforce stone walls.
3. Re-laying of dilapidated brick cornices, lintels of pit parapets and protruding parts of walls.
4. Relocation and repair of individual dilapidated sections of stone walls up to 20% of the total volume of masonry, not related to the superstructure of the building or additional loads from newly installed equipment.
5. Strengthening of reinforced concrete and stone columns with clips.
6. Repair and partial replacement (up to 20% of the total volume) of columns that are not associated with additional loads from newly installed equipment.
7. Change of aggregates in walls with stone, reinforced concrete and metal frames (up to 40%).
8. Change of dilapidated crowns of log or block walls (up to 20% of the total surface of the walls).
9. Continuous caulking of log or block walls.
10. Partial replacement of sheathing, backfilling and slab heaters of frame walls (up to 50% of the total wall area).
11. Change or repair of sheathing and insulation of wooden plinths.
12. Repair of stone plinths of wooden walls with their re-laying up to 50% of the total volume.
13. Setting up again and changing worn clamps of log and block walls.
III. Partitions
1. Repair, change and replacement of worn-out partitions with more advanced designs of all types of partitions.
2. During the overhaul of partitions, partial redevelopment is allowed with an increase in the total area of the partitions by no more than 20%.
IV. Roofs and coverings
1. Replacing dilapidated wooden roof trusses or replacing them with prefabricated reinforced concrete.
2. Complete or partial replacement of dilapidated metal and reinforced concrete trusses, as well as replacement of metal trusses with prefabricated reinforced concrete trusses.
3. Reinforcement of trusses when replacing types of coating (replacing wood slabs with precast concrete, cold coating - with warm, etc.), during suspension of lifting devices, as well as during corrosion of nodes and other elements of metal and prefabricated reinforced concrete trusses.
4. Partial or complete change of rafters, mauerlats and battens.
5. Repair of supporting structures of skylights.
6. Repair of devices for opening the covers of skylights.
7. Partial or complete replacement of dilapidated elements of coatings, as well as replacing them with more progressive and durable ones.
8. Partial (over 10% of the total roof area) or complete change or replacement of all types of roofing.
9. Reconstruction of roofs in connection with the replacement of the roofing material.
10. Partial or complete replacement of wall gutters, slopes and covers of chimneys and other protruding devices above the roof.
V. Interfloor ceilings and floors
1. Repair or change of floors.
2. Replacing individual structures or ceilings as a whole with more progressive and durable structures.
3. Strengthening of all types of interfloor and attic floors.
4. Partial (more than 10% of the total floor area in the building) or complete replacement of all types of floors and their bases.
5. Reconstruction of floors during repairs with replacement with stronger and more durable materials. In this case, the type of floors must comply with the requirements of standards and specifications for new construction.
VI. Windows, doors and gates
1. Complete replacement of dilapidated window and door blocks, as well as gates of industrial buildings.
VII. Stairs and porches
1. Partial or complete change of landings, ramps and porches.
2. Change and strengthening of all types of stairs and their individual elements.
VIII. Internal plastering, facing
and painting work
1. Renewal of plastering of all premises and repair of plastering in the amount of more than 10% of the total plastered surface.
2. Change of wall cladding in the amount of more than 10% of the total area of clad surfaces.
3. Continuous anti-corrosion painting of metal structures.
IX. facades
1. Repair and renewal of lining with an area of more than 10% of the lined surface.
2. Full or partial (more than 10%) renewal of the plaster.
3. Complete renewal of rods, cornices, belts, sandriks, etc.
4. Renewal of stucco details.
5. Continuous coloring with stable compositions.
6. Cleaning the facade with sandblasters.
7. Change of balcony slabs and railings.
8. Change of coatings of the protruding parts of the building.
1. Complete refurbishment of all types of heating furnaces, chimneys and their foundations.
2. Re-equipment of furnaces for burning coal and gas in them.
3. Complete refurbishment of kitchen stoves.
XI. Central heating
1. Change of individual sections and assemblies of heating boilers, boilers, boiler units or complete replacement of boiler units (in the event that the boiler unit is not an independent inventory object).
2. Repair and replacement of expanders, steam traps and other network equipment.
3. Repair and re-laying of foundations for boilers.
4. Automation of boiler rooms.
5. Transfer from stove heating to central heating.
6. Change of heating registers.
7. Connection of buildings to heating networks (with a distance from the building to the network of no more than 100 m).
XII. Ventilation
1. Partial or complete change of air ducts.
2. Change fans.
3. Rewinding or changing electric motors.
4. Change of gates, deflectors, throttle valves, blinds.
5. Partial or complete change of ventilation ducts.
6. Change of heaters.
7. Change of heating units.
8. Change filters.
9. Change of cyclones.
10. Change of individual chamber designs.
XIII. Water supply and sewerage
1. Partial or complete change of piping inside the building, including water supply inlets and sewer outlets.
XIV. Hot water supply
1. Change of coils and boilers.
2. Change of the pipeline, parts and, in general, pumping units, tanks and pipeline insulation.
XV. Electrical lighting and communications
1. Change of worn-out sections of the network (more than 10%).
2. Change of safety guards.
3. Repair or restoration of cable channels.
4. During the overhaul of the network, it is allowed to replace lamps with other types (ordinary ones with fluorescent ones).
B. BY FACILITIES
XVI. Water supply and sewerage facilities
a) Pipelines and network fittings
1. Partial or complete replacement of anti-corrosion insulation of the pipeline.
2. Change of individual pipeline sections (due to pipe wear) without changing the pipe diameter. At the same time, it is allowed to replace cast-iron pipes with steel pipes, ceramic pipes with concrete or reinforced concrete pipes and vice versa, but it is not allowed to replace asbestos-cement pipes with metal pipes (except in emergency cases).
3. Change of worn fittings, valves, fire hydrants, air vents, valves, standpipes or their repair with the replacement of worn parts.
4. Change of individual siphon pipes.
b) Wells
1. Repair of cell wells.
2. Change hatches.
3. Stuffing new trays to replace the destroyed ones.
4. Replacement of worn-out wooden wells.
5. Renewal of plaster.
c) Water intakes and hydraulic structures
1. Dams, dams, spillways, canals
1. Change or replacement of fastening of banks or slopes in the amount of up to 50%.
2. Filling up swollen slopes of earthworks.
3. Change of clothes.
4. Renewal of the protective layer in the underwater parts of reinforced concrete structures.
5. Change of lattices and grids.
6. Repair and replacement of shield gates.
2. Water wells
1. Construction and dismantling of an oil rig or installation and dismantling of an inventory drilling rig.
2. Cleaning the well from collapses and siltation.
3. Removing and installing a new filter.
4. Fixing the well with a new column of casing pipes.
5. Replacement of water and air pipes.
6. Restoration of well flow rate by torpedoing or flushing with hydrochloric acid.
7. Cementation of the annular space and drilling of cement.
d) Treatment facilities
1. Repair and replacement of fully waterproofing.
2. Repair and renewal of plaster and ironwork.
3. Relaying brick walls and partitions up to 20% of the total volume of masonry in the building.
4. Sealing leaks in reinforced concrete, concrete and stone walls and bottoms of structures with concrete dismantling in separate places and concrete again.
5. Continuous gunning of the walls of structures.
6. Repair of drainage around structures.
7. Replacement of tank hatches.
8. Replacement of gratings.
9. Replacement of loading filters, biofilters, air filters.
10. Change of filter plates.
11. Replacement of pipelines and fittings.
12. Translation drainage system silt sites.
XVII. Heat supply
a) Channels and cameras
1. Partial or complete change of coatings of channels and chambers.
2. Partial or complete change of waterproofing of channels and chambers.
3. Partial re-laying of the walls of brick channels and chambers (up to 20% of the total surface of the walls).
4. Partial relocation of drainage systems.
5. Repair of the bottoms of channels and chambers.
6. Renewal of the protective layer in reinforced concrete structures of channels and chambers.
7. Change hatches.
b) Pipelines and fittings
1. Partial or complete change of thermal insulation of the pipeline.
2. Renewal of pipeline waterproofing.
3. Change of individual sections of the pipeline (due to pipe wear) without increasing the diameter of the pipes.
4. Change of fittings, valves, compensators or their repair with the replacement of worn parts.
5. Replacement of movable and fixed supports.
XVIII. Access and internal railway tracks
a) ground bed
1. Broadening of the subgrade in places of insufficient width to normal sizes.
2. Treatment of subgrade in places of landslides, erosion, landslides, abysses.
3. Restoration of all drainage and drainage devices.
4. Restoration of all protective and fortifying structures of the subgrade (sodding, paving, retaining walls).
5. Restoration of regulatory structures.
6. Correction, filling up the cones of bridges.
7. Change of individual structures of artificial structures or their replacement with other structures, as well as a complete change of pipes and small bridges (if they are not independent inventory objects, but are part of the subgrade).
b) The superstructure of the track
1. Cleaning the ballast layer or updating the ballast with bringing the ballast prism to the dimensions established by the standards for this type of track.
2. Change of unusable sleepers.
3. Change of worn rails.
4. Change of unusable fasteners.
5. Straightening curves.
6. Repair of turnouts with the replacement of individual elements and transfer bars.
7. Change of turnouts.
8. Repair of the bridge deck.
9. Change of flooring of crossings or replacement of wood with reinforced concrete.
c) Artificial structures (bridges, tunnels, pipes)
1. Partial replacement of elements or complete replacement of worn-out superstructures.
2. Partial re-laying of stone and brick supports (up to 20% of the total volume).
3. Repair of concrete supports (up to 15% of the total volume).
4. Gunning or grouting of the surface of the supports.
5. Arrangement on supports of reinforcing reinforced concrete shells (jackets).
6. Repair or complete change of insulation.
7. Change of bridge beams.
8. Change of anti-theft bars.
9. Change of wooden flooring.
10. Change of flooring from reinforced concrete slabs.
11. Change of counter rails.
12. Change of damaged elements of wooden bridges, except for piles.
13. Replacement of wooden packages with reinforced concrete superstructures.
14. Partial re-laying of stone and brickwork of vaults and walls of tunnels.
15. Injection of cement mortar behind the tunnel lining.
16. Repair and replacement of drainage devices of tunnels.
17. Relocation of the pipe head.
18. Change of elements of wooden pipes (up to 50% of the volume of wood).
19. Change of elements of reinforced concrete or concrete pipes (up to 50% of the volume).
XIX. Car roads
a) ground bed
1. Treatment of subgrade in places of landslides, landslides, erosion and deeps.
2. Restoration of all drainage and drainage devices.
3. Restoration of all protective and fortifying structures of the subgrade.
4. Change of individual structures of artificial structures or their replacement with other structures, as well as a complete change of pipes and small bridges (if they are not independent inventory objects, but are part of the subgrade or road as a single inventory object).
b) Road clothes
1. Alignment and replacement of individual cement-concrete slabs.
2. Laying a leveling layer of asphalt concrete on the cement-concrete surface.
3. Installation of asphalt concrete pavement on roads with cement-concrete pavement.
4. Change of cement-concrete coating to a new one.
5. Strengthening the asphalt concrete pavement.
6. Reconstruction of crushed stone and gravel coatings.
7. Relocation of pavements.
8. Profiling of dirt roads.
c) Bridges, pipes
1. Partial re-laying of stone and brick supports (up to 20% of the total volume).
2. Repair of concrete supports (up to 15% of the total volume).
3. Change of damaged elements of wooden bridges, except for piles.
4. Change of wooden or reinforced concrete flooring, as well as replacement of wooden flooring with reinforced concrete.
5. Complete change or replacement of superstructures.
6. Relocation of pipe heads.
7. Change of elements of wooden, reinforced concrete or concrete pipes (up to 50% of the volume).
d) Sites for cars, road construction
and other machines, storage areas, as well as areas
grain receiving points
1. Repair and restoration of drainage structures (trays, ditches, etc.).
2. Relocation of cobblestone areas.
3. Reconstruction of crushed stone and gravel surfaces of sites.
4. Repair of concrete pads with laying a leveling layer of concrete.
5. Alignment and replacement of individual cement-concrete slabs.
6. Covering with asphalt concrete the sites listed in paragraphs 2 - 5.
XX. Electrical networks and communications
1. Change or replacement of unusable fittings.
2. Replacing hooks with traverses.
3. Change wires.
4. Repair and change of end and connecting cable boxes.
5. Repair or replacement of grounding devices.
6. Change of supports (up to 30% per 1 km).
7. Installation of cable wells.
XXI. Other structures
1. Repair, change or replacement with other supports of racks for air laying of pipelines.
2. Repair or change of platforms, stairs and railings for overhead pipelines.
3. Repair or replacement of individual columns (up to 20%) of crane racks.
4. Repair or change of crane beams of crane racks.
5. Repair of galleries and fuel supply racks of boiler houses and gas generator substations with a change (up to 20%) of structures without changing foundations.
6. Change or complete replacement of wooden fence posts (fences).
7. Repair or replacement of individual concrete and reinforced concrete pillars (up to 20%) and fences (fences).
8. Repair of individual sections of filling between fence posts (up to 40%).
9. Repair of separate sections of solid stone fences (up to 20%).
10. Repair of individual sections of solid adobe fences (up to 40%).
11. Repair of chimneys with the change or replacement of the lining, with the installation of hoops, with the restoration of the protective layer of reinforced concrete pipes.
12. Repair and replacement of individual sections of metal chimneys.
13. Repair of ash and slag dischargers with complete replacement of individual sections of the pipeline (without increasing the diameter).
14. Repair of loading platforms with a complete change of wooden flooring, blind area or asphalt. Change of individual supports or sections of retaining walls (up to 20%). In the event that the unloading area is part of a storage facility (ramp), a complete change or replacement of all structures is allowed.
An approximate list of works performed during the overhaul of the housing stock; Appendix 8 to the Decree of the Gosstroy of the Russian Federation of September 27, 2003 N 170 "On approval of the Rules and norms for the technical operation of the housing stock"
1. Inspection of residential buildings (including a complete survey of the housing stock) and preparation of design estimates (regardless of the period of repair work).
2. Repair and construction work to change, restore or replace elements of residential buildings (except for the complete replacement of stone and concrete foundations, load-bearing walls and frames).
3. Modernization of residential buildings during their overhaul (re-planning, taking into account the downsizing of multi-room apartments; installation of additional kitchens and sanitary facilities, expansion of living space due to auxiliary premises, improvement of insolation of residential premises, elimination of dark kitchens and entrances to apartments through kitchens with a device, with necessary, built-in or attached premises for stairwells, sanitary facilities or kitchens); replacement of furnace heating with central heating with the installation of boiler rooms, heat pipelines and heat points; roof and other autonomous sources of heat supply; re-equipment of furnaces for burning gas or coal in them; equipment with cold and hot water supply, sewerage, gas supply systems with connection to existing main networks with a distance from the input to the point of connection to the mains up to 150 m, the installation of gas ducts, water pumps, boiler rooms; complete replacement of existing central heating systems, hot and cold water supply (including the mandatory use of modernized heating devices and pipelines made of plastic, metal-plastic, etc. and a ban on the installation of steel pipes); installation of household electric stoves instead of gas stoves or kitchen hearths; installation of elevators, garbage chutes, pneumatic waste disposal systems in houses with a landing of the upper floor of 15 m and above; transfer of the existing power supply network to increased voltage; repair of television antennas for collective use, connection to the telephone and radio broadcasting networks; installation of intercoms, electric locks, installation of fire-fighting automation and smoke removal systems; automation and dispatching of elevators, heating boilers, heating networks, engineering equipment; landscaping of courtyard areas (paving, asphalting, landscaping, fencing, wood sheds, equipment for children's and household playgrounds). Repair of roofs, facades, joints of prefabricated buildings up to 50%.
4. Insulation of residential buildings (works to improve the heat-shielding properties of enclosing structures, the installation of window fillings with triple glazing, the installation of external vestibules).
5. Replacement of intra-quarter engineering networks.
6. Installation of metering devices for the consumption of thermal energy for heating and hot water supply, the consumption of cold and hot water for the building, as well as the installation of apartment meters for hot and cold water (when replacing networks).
7. Reconstruction of non-ventilated combined roofs.
8. Author's supervision of design organizations for the overhaul of residential buildings with full or partial replacement of ceilings and redevelopment.
9. Technical supervision in cases where subdivisions for technical supervision of major repairs of the housing stock have been created in local governments and organizations.
10. Repair of built-in premises in buildings.
List of works on major repairs of buildings and structures; Appendix 9 to the Order of the Ministry of Justice of Russia dated September 28, 2001 N 276 (as amended on January 24, 2006) "On approval of the instructions for the technical operation of buildings and structures of institutions of the penitentiary system")
Annex 9
1.1. Foundations.
1.1.1. Changing wooden chairs or replacing them with stone or concrete pillars.
1.1.2. Partial re-laying (up to 15%), as well as strengthening of foundations and basement walls under the outer and inner walls and pillars of stone and wooden buildings that are not connected with the superstructure of the building or with additional loads from newly installed equipment.
1.1.3. Strengthening the foundations for the foundations of stone buildings that are not related to the superstructure of the building.
1.1.4. Restoration of vertical and horizontal insulation of foundations.
1.1.5. Restoration of the settled existing or construction of a new blind area around the building (more than 20% of the total blind area) in order to protect the soil under the foundations from erosion or waterlogging.
1.1.6. Repair of brick cladding of foundation walls from the basement side in separate places with the laying of more than 10 bricks in one place.
1.1.7. Partial or complete restoration or installation of new waterproofing in the basement.
1.1.8. Partial or complete re-laying of pits at the windows of the basement and basement floors.
1.1.9. Replacing rotten wooden foundation chairs in wooden buildings with new wooden, brick, concrete or reinforced concrete pillars.
1.1.10. Repair of existing drains around the building.
1.1.11. Replacement of single collapsing stone and concrete pillars.
Note. At the expense of funds for major repairs, it is possible to artificially fix the soils of the bases of foundations by chemical, thermal and other methods.
1.2. Walls and columns.
1.2.1. Relaying brick plinths (more than 10 bricks in one place).
1.2.2. Sealing of cracks in brick or stone walls with furrow clearing, with dressing of seams with old masonry.
1.2.3. Arrangement and repair of structures reinforcing stone walls.
1.2.4. Relaying dilapidated brick cornices, lintels, parapets, pits and protruding parts of walls.
1.2.5. Full or partial re-laying and fastening of individual dilapidated sections of brick walls (up to 25% of their total area in the building) that are not associated with the superstructure of the building or with additional loads from newly installed equipment, as well as the change of individual crowns in wooden buildings, also not exceeding 25% common wall surface.
1.2.6. Reinforcement of walls with tension and metal ties.
1.2.7. Change of fillings in walls with stone, reinforced concrete and metal frames (up to 40%).
1.2.8. Sealing cracks in brick walls with excavation and clearing of old masonry and installation of a new one, with dressing of seams with old masonry.
1.2.9. Restoration of the waterproofing layer of the entire horizontal plane along the edge of the foundation.
1.2.10. Fastening or strengthening of stone walls that deviate from the vertical position and have deformations.
1.2.11. Relaying dilapidated cornices, parapets, firewalls, pits and protruding parts of walls.
1.2.12. Relaying individual, worn out, window and door lintels.
1.2.13. Insulation of dilapidated wooden walls with striped boards over roofing or with additional sheathing with boards and backfilled with fine slag.
1.2.14. Partial dismantling of existing internal walls and laying of new ones (up to 25% of the total volume) associated with the redevelopment of premises.
1.2.15. Replacement of various types of aggregates in walls with stone, reinforced concrete and metal frames (up to 50% of the total wall area).
1.2.16. Change of dilapidated crowns of log or block walls (up to 20%).
1.2.17. Continuous caulking of log or block walls.
1.2.18. Partial replacement of sheathing, backfilling and slab insulation of frame walls (up to 50% of the total wall area).
1.2.19. Change or repair of sheathing and insulation of wooden plinths.
1.2.20. Repair of stone plinths of wooden walls with their re-laying up to 50% of the total volume.
1.2.21. Setting up again and changing worn clamps of log and block walls.
1.2.22. Strengthening reinforced concrete and stone columns with clips.
1.2.23. Repair and partial replacement (up to 20%) of columns not associated with additional loads from newly installed equipment.
1.3. Partitions.
1.3.1. Repair, change and replacement of worn partitions with more advanced designs.
1.3.2. Partial redevelopment with an increase in the total area of the partitions (up to 20%).
1.3.3. Repair of partitions with the replacement of unusable strappings and boards in the amount of more than 2 m2 in one place.
1.3.4. Strengthening the sound insulation of partitions by upholstering them with an additional layer of hardboard, cardboard or other materials, followed by applying a layer of plaster, wallpapering or painting.
1.3.5. Replenishment of the backfill of two-layer partitions, followed by boarding and all finishing work.
1.4. Roofs and roofs.
1.4.1. Replacement of formwork boards in places of grooves and eaves slopes.
1.4.2. Replacement of dilapidated roof structures with a roof made of prefabricated reinforced concrete elements coated with roofing felt, roofing material and other roofing materials.
1.4.3. Full or partial replacement of dilapidated metal and reinforced concrete trusses.
1.4.4. Strengthening trusses when replacing types of coatings (wood-based panels with precast concrete, cold coating with warm coating, etc.), as well as with corrosion of nodes and other elements of metal and prefabricated reinforced concrete trusses.
1.4.5. Partial or complete replacement of rafters, mauerlats and battens under the roof.
1.4.6. Repair or replacement of worn-out metal railings on roofs.
1.4.7. Repair or replacement of worn outdoor fire escapes.
1.4.8. Installation of new manholes on the roof, dormer windows and transitional bridges to them.
1.4.9. Relocation of chimney and ventilation pipes on the roof.
1.4.10. Continuous replacement of dilapidated wall gutters, slopes and covers around chimneys and other protruding devices above the roof.
1.4.11. Reconstruction of light lanterns with low illumination of premises to a large one.
1.4.12. Repair and painting of the supporting structures of skylights.
1.4.13. Repair of mechanical and manual opening and closing devices of skylight bindings.
1.4.14. Partial or complete replacement of dilapidated coating elements, as well as replacing them with more progressive and durable ones.
1.4.15. Partial (more than 10%) or complete change or replacement of the roof (all types).
1.4.16. Reconstruction of roofs in connection with the replacement of roofing materials.
1.4.17. Repair of coatings around chimneys and ventilation pipes, firewalls, parapets and other protruding parts on the roof.
1.4.18. Strengthening of parapets, steel gratings of the fence, repair of ventilation shaft heads, gas ducts, sewer risers and other protruding parts on the roof.
1.4.19. Restoration and repair of stepladders for the safe cleaning of chimneys on roofs with soft coatings or slopes with a steep slope.
1.4.20. Maintenance of outdoor fire escapes for climbing to the roof.
1.5. Interfloor ceilings and floors.
1.5.1. Repair or replacement of interfloor and attic floors.
1.5.2. Replacing individual floor beams, building up the ends of the beams with prostheses with all subsequent work. Replacing the selection between the beams.
1.5.3. Replacing individual structures or ceilings as a whole with more progressive and durable structures.
1.5.4. Strengthening of all elements of interfloor and attic floors.
1.5.5. Gunning of reinforced concrete floors in case of their damage.
1.5.6. Partial (more than 10%) or continuous change of floors (of all types) and their bases.
1.5.7. Reconstruction of floors during repairs with replacement with stronger and more durable ones, while the type of floors must comply with the requirements of norms and specifications for new construction.
1.5.8. Restoration of the concrete base under the floors with the installation of a new floor.
1.5.9. Re-laying clean plank floors with leveling the lag and adding new material.
1.5.10. Re-laying of parquet floors with correction or replacement of lathing.
1.5.11. Re-laying of floors on logs in the ground floors with correction or replacement of the base and restoration of brick columns.
1.5.12. Repair or replacement of underground canal walls.
1.6. Windows, doors and gates.
1.6.1. Complete replacement of dilapidated window and door blocks, as well as gates.
1.7. Stairs and porches.
1.7.1. Partial or complete change of landings, ramps and porches.
1.7.2. Change or strengthening of all types of stairs and their individual elements.
1.7.3. Replacement or repair of railings and handrails of stairs over 5% of their total number.
1.7.4. Installation of new porches.
1.7.5. Change of metal stringers or welding of damaged parts of stringers.
1.8. Internal plastering, facing and painting works.
1.8.1. Renewal of plastering of all premises and repair of plastering in the amount of more than 10% of the total plastered surface.
1.8.2. Upholstery of walls and ceilings with dry plaster.
1.8.3. Restoration or replacement of wall surface cladding in the amount of more than 10% of the total area of cladding surfaces.
1.8.4. Renewal of stucco details indoors.
1.8.5. Painting of window casings, doors, ceilings, walls and floors after the overhaul of these structures.
1.8.6. Oil painting of radiators, heating pipes, water supply, sewerage, gasification after a major overhaul of the system or its new installation, if the costs are incurred at the expense of capital repairs.
1.8.7. Continuous anti-corrosion painting of metal structures.
1.9. facades.
1.9.1. Repair and renewal of cladding with an area of more than 10% of the cladded surface of building facades with the replacement of individual tiles with new ones or plastering of these places with subsequent painting to match the color of the facing slabs.
1.9.2. Full or partial (more than 10%) renewal of the plaster.
1.9.3. Restoration or alteration of rods, cornices, belts, sandriks and other protruding parts of building facades.
1.9.4. Continuous replacement and installation of new drainpipes, as well as all external metal and cement coatings on the protruding parts of building facades.
1.9.5. Restoration of molding and stucco decorations and details.
1.9.6. Continuous painting of building facades with stable compositions.
1.9.7. Change or installation of new gratings and fences on the roofs and balconies of buildings.
1.9.8. Cleaning of facades and plinths with sandblasters.
1.9.9. Change or strengthening of all load-bearing and enclosing structures of balconies and bay windows.
1.9.10. Change of coverings of protruding parts of the building.
1.9.11. Restoration of old or installation of new gates.
1.9.12. Oil painting of facades of wooden buildings.
1.10. Furnaces and hearths.
1.10.1. Repair, alteration and installation of new stoves, kitchen hearths, cast-in boilers and chimneys for them.
1.10.2. Complete refurbishment or installation of new heating stoves, chimneys, ventilation ducts and chimneys and their foundations.
1.10.3. Re-equipment of heating stoves from wood to gas heating or heating with solid fuel.
1.11. Central heating.
1.11.1. The device of central heating instead of the stove with the adaptation of the existing room for a boiler room and the installation of a boiler room. AT individual cases, if it is impossible to adapt the existing premises for the boiler room, it is allowed to carry out an extension to existing building premises with a built-up area of not more than 65 m2 or build a new boiler building.
1.11.2. Change of individual sections and assemblies of heating boilers, boilers, boiler units or complete replacement of boiler units (if they are not independent inventory objects).
1.11.3. Replacement of the existing central heating pipeline.
1.11.4. Repair and replacement of expanders, steam traps and other network equipment.
1.11.5. The device of remote furnaces and devices for boilers under the blast furnace.
1.11.6. Change and installation of additional sections of heating devices and individual sections of the pipeline.
1.11.7. Repair, re-laying or re-installation of foundations for boilers and other equipment.
1.11.8. Boiler room automation.
1.11.9. Replacing the insulation of pipelines that have become unusable.
1.11.10. Refurbishment of the lining of the boiler and chimneys.
1.11.11. Putting patches on a steel boiler, boiler, steamer, tank.
1.11.12. Manufacture and installation of a new casing.
1.11.13. Restoration or installation of a new lining and lining of central heating boilers.
1.11.14. Replacement of worn-out metal chimneys from boiler rooms.
1.11.15. Change of heating registers.
1.11.16. Connection of buildings to heating networks (with a distance from the building to the network of no more than 100 m).
1.12. Ventilation.
1.12.1. Installation of a new, restoration or reconstruction of the ventilation system.
1.12.2. Partial or complete replacement of air ducts.
1.12.3. Changing fans.
1.12.4. Rewinding or changing electric motors.
1.12.5. Change of gates, deflectors, throttle valves, blinds.
1.12.6. Partial or complete replacement of ventilation ducts.
1.12.7. Change of heaters.
1.12.8. Change of heating units.
1.12.9. Changing filters.
1.12.10. change of cyclones.
1.12.11. Change of individual designs of ventilation chambers.
1.13. Plumbing and sewerage.
1.13.1. Restoration or installation of a new internal water supply and sewerage of the building, pipelines, including water supply and sewerage outlets and their connection to the water supply and sewerage networks. The length of the line from the nearest water inlet or sewer outlet to the street network should not exceed 100 m.
1.13.2. Installation of new water intakes indoors.
1.13.3. Installation of additional manholes on existing yard lines or street networks at the points of connection.
1.13.4. Laying of underground lines of water and sewer pipes.
1.13.5. Replacing the cast-iron cisterns of the latrines with flush taps with alteration of the piping and shortening of the flush pipe.
1.13.6. Replacement of taps, valves and sanitary appliances.
1.13.7. Water tower device.
1.13.8. Installation of new sanitary facilities.
1.14. Hot water supply.
1.14.1. Change and installation of a new hot water supply.
1.14.2. Change of individual sections of the hot water pipeline.
1.14.3. Replacing worn-out tanks, water heaters and water heaters.
1.14.4. Repair of tanks, coils and boilers, associated with complete disassembly and replacement of individual components and parts.
1.14.5. Change of pipeline, parts and in general pumping units, tanks and pipeline insulation.
1.14.6. Change and installation of baths, showers and fittings for them (shower nets with pipelines, taps, flexible hoses).
1.15. Electrical lighting, communications and power wiring.
1.15.1. Installation of new electric lighting in residential and public buildings and connection to the power supply network.
1.15.2. Replacement of worn-out lighting wiring with a change of installation fittings (switches, knife switches, plugs, cartridges, sockets), and in the event of a major overhaul of the building - the installation of new electrical wiring.
1.15.3. Installation of new and replacement of group distribution and safety boxes and shields.
1.15.4. Reconstruction of electrical wiring with the installation of additional fittings in connection with the redevelopment of the premises.
1.15.5. Automation of electric lighting in stairwells of buildings.
1.15.6. Replacement of metering devices and protection devices for electrical installations.
1.15.7. Repair or restoration of cable channels.
1.15.8. Replacement of lamps for other types (conventional for fluorescent, etc.).
1.16. Gas supply.
1.16.1. Installation of additional gas equipment in apartments with its connection to the gas network.
1.16.2. Gasification of individual apartments.
1.16.3. Change of individual sections of the gas pipeline.
1.16.4. Replacement of equipment that has become unusable (gas stoves, water heaters) with new equipment.
1.17. Elevators and lifts.
1.17.1. Re-installation of elevators with all types of construction and installation works.
1.17.2. Full or partial replacement of electrical equipment and cargo elevator winches.
1.17.3. Strengthening, full or partial change of metal structures and fencing nets of the mine.
1.17.4. Complete or partial change of electrical wiring in mines.
1.17.5. Dismantling and installation of elevator equipment in connection with work to reduce noise in premises with a permanent presence of people.
1.17.6. Elevator automation.
2. Structures
2.1. Water supply and sewerage facilities. Pipelines and network fittings.
2.1.1. Partial or complete replacement of anti-corrosion pipeline insulation.
2.1.2. Change of individual sections of the pipeline without changing the diameter of the pipes. At the same time, it is allowed to replace cast-iron pipes with steel pipes, ceramic pipes with concrete or reinforced concrete pipes and vice versa, but it is not allowed to replace asbestos-cement pipes with metal pipes (except in emergency cases).
The length of network sections where a continuous change of pipes is allowed should not exceed 200 m per 1 km of the network.
2.1.3. Change of worn fittings, valves, fire hydrants, air vents, valves, standpipes or their repair with the replacement of worn parts.
2.1.4. Change of individual siphon pipes.
2.2. Water supply and sewer networks. Wells.
2.2.1. Repair of masonry wells.
2.2.2. Changing hatches.
2.2.3. Stuffing again trays to replace the destroyed ones.
2.2.4. Replacing worn-out wooden wells.
2.2.5. Restoration of plaster.
2.3. Water supply and sewer networks. Treatment facilities.
2.3.1. Repair or replacement (totally) waterproofing.
2.3.2. Repair and renewal of plaster and ironing.
2.3.3. Relaying brick walls and partitions (up to 20% of the total volume of masonry in the building).
2.3.4. Sealing leaks in reinforced concrete, concrete and stone walls and bottoms of structures with concrete dismantling in separate places and concreting again.
2.3.5. Continuous shotcrete of the walls of structures.
2.3.6. Repair of drainage around structures.
2.3.7. Replacement of hatches of tanks.
2.3.8. Grating replacement.
2.3.9. Replacement of loading of filters, biofilters, aerofilters.
2.3.10. Replacement of pipelines and fittings.
2.3.11. Change of filter plates.
2.3.12. Relaying the drainage system of silt pads.
2.4. Heat supply. channels and cameras.
2.4.1. Partial or complete change of coatings of channels and chambers.
2.4.2. Partial or complete change of waterproofing of channels and chambers.
2.4.3. Partial re-laying of the walls of brick channels and chambers (up to 20% of the total surface of the walls).
2.4.4. Partial relocation of drainage systems.
2.4.5. Repair of the bottoms of channels and chambers.
2.4.6. Renewal of the protective layer in reinforced concrete structures of channels and chambers.
2.4.7. Changing hatches.
2.5. Heat supply. Pipelines and fittings.
2.5.1. Partial or complete change of thermal insulation of the pipeline.
2.5.2. Renewal of pipeline waterproofing.
2.5.3. Change of individual sections of the pipeline without increasing the diameter of the pipes.
2.5.4. Change of fittings, valves, compensators or their repair with the replacement of worn parts.
2.5.5. Replacement of movable and fixed supports.
2.6. Car roads. Ground cloth.
2.6.1. Treatment of subgrade in places of landslides, landslides, erosion and abysses.
2.6.2. Restoration of drainage and drainage devices.
2.6.3. Restoration of protective and fortifying structures of the subgrade.
2.6.4. Change of individual structures of artificial structures or their replacement with other structures, as well as a complete change of pipes and small bridges (if they are not independent inventory objects, but are part of the subgrade or road as a single inventory object).
2.7. Car roads. Road clothes.
2.7.1. Alignment and replacement of individual cement-concrete slabs.
2.7.2. Laying a leveling layer of asphalt concrete on a cement-concrete surface.
2.7.3. Installation of asphalt concrete pavement on roads with cement-concrete pavement.
2.7.4. Change of cement-concrete pavement to a new one.
2.7.5. Strengthening of asphalt concrete pavement.
2.7.6. Reconstruction of crushed stone and gravel coverings.
2.7.7. Relocation of bridges.
2.7.8. Profiling of dirt roads.
2.8. Warehouse and other sites.
2.8.1. Repair and restoration of drainage structures (trays, ditches, etc.).
2.8.2. Relocation of cobblestone areas.
2.8.3. Reconstruction of crushed stone and gravel coverings of sites.
2.8.4. Repair of concrete platforms with laying of a leveling layer of concrete.
2.8.5. Leveling and replacement of individual cement-concrete pads.
2.8.6. Covering sites with asphalt concrete.
2.9. Electrical networks and communications.
2.9.1. Change or replacement of fittings.
2.9.2. Replacing hooks with traverses.
2.9.3. Wire change.
2.9.4. Repair and change of end and connecting cable boxes.
2.9.5. Repair or replacement of grounding devices.
2.9.6. Change of supports (up to 30% per 1 km).
2.9.7. Installation of cable wells.
2.10. Other buildings.
2.10.1. Repair, change or replacement with other supports of racks for air laying of pipelines.
2.10.2. Repair and replacement of platforms, stairs and railings for overhead pipelines.
2.10.3. Repair or change of individual columns (up to 20%) of crane racks.
2.10.4. Repair or change of crane beams of crane racks.
2.10.5. Repair of galleries and fuel supply racks of boiler and gas generating substations with a change (up to 20%) of structures without changing foundations.
2.10.6. Change or complete replacement of wooden fence posts.
2.10.7. Repair or change of individual concrete and reinforced concrete pillars (up to 20%) of fences.
2.10.8. Repair of individual sections of fencing elements (up to 40% filling between posts).
2.10.9. Repair of separate sections of solid stone fences (up to 20%).
2.10.10. Repair of individual sections of solid adobe fences (up to 40%).
2.10.11. Repair of chimneys with the change or replacement of the lining, with the installation of hoops, with the restoration of the protective layer of reinforced concrete pipes.
2.10.12. Repair and replacement of individual sections of metal chimneys.
2.16.13. Repair of ash and slag dischargers with complete replacement of individual sections of pipelines (without increasing the diameter).
2.12.14. Repair of loading platforms with a complete change of wooden flooring, blind area or asphalt. Change of individual supports or sections of retaining walls (up to 20%). If the unloading area is part of a storage facility (ramp), a complete change or replacement of all structures is allowed.
The list of works on the overhaul of apartment buildings to be included in the scope of works financed from the funds provided for by Federal Law N 185-FZ; Table 2.3 ( "Methodological recommendations for the formation of the scope of works for the overhaul of apartment buildings financed from the funds provided for by the Federal Law of July 21, 2007 N 185-FZ "On the Fund for Assistance to the Reform of the Housing and Communal Services" (approved by the State Corporation "Fund for Assistance to the Reform of Housing and Utilities" 15.02.2013)
This list is formed on the basis of the updated lists of work on major repairs recommended by the above regulatory documents within the framework of the types of work on the overhaul of apartment buildings, defined by Article 15 of the Federal Law N 185-FZ. It is assumed, however, that the provisions of these guidelines apply to apartment buildings subject to major repairs without stopping their operation. As a result of the overhaul, all necessary work must be performed to bring the common property of an apartment building into a technically sound condition by restoring or replacing all parts of structures and engineering systems that have more short time service between the next (according to the standard service life) overhauls than the supporting structures.
2.3.2. Consistent and methodical binding technological processes to the list of works given in Table 2.3 of these recommendations is contained in Section 3.
Table 2.3
|
Name of types of work in accordance with Part 3 of Article 15 of Federal Law N 185-FZ |
Subspecies and list of works |
|
|
Repair of intra-house engineering systems of electricity, heat, gas, water supply, sanitation |
1. Repair or replacement of engineering systems: |
|
|
1.1. Cold water supply, including: |
||
|
1.1.1. Repair or replacement of water meter units; |
||
|
1.1.2. Repair or replacement of distributing highways and risers; |
||
|
1.1.3. Replacement of shut-off valves, including those on a branch from the risers to the apartment; |
||
|
1.1.4. Repair or replacement in the complex of equipment of booster pumping units |
||
|
1.1.5. Repair or replacement of equipment, pipelines and fire water supply equipment |
||
|
1.2. Repair or replacement of the hot water system, including: |
||
|
1.2.1. Repair or replacement of TRZH, heat exchangers, boilers, pumping units and other equipment (as part of the common property) in the complex for the preparation and supply of hot water to the distribution network; |
||
|
1.2.2. Repair or replacement of distributing highways and risers; |
||
|
1.2.3. Replacement of shut-off valves, including those on a branch from the risers to the apartment. |
||
|
1.3. Repair or replacement of the sewerage and drainage system, including: |
||
|
1.3.1. Repair or replacement of outlets, prefabricated pipelines, risers and hoods; |
||
|
1.3.2. Replacing valves, if any; |
||
|
1.4. Repair or replacement of the heating system, including; |
||
|
1.4.1. Repair or replacement of distributing highways and risers; |
||
|
1.4.2. Replacement of shut-off and control valves, including those on a branch from risers to heating appliances in residential premises; |
||
|
1.4.3. Regrouping or replacement of heating devices in common areas and replacement of heating devices in residential premises that do not have disconnecting devices; |
||
|
1.4.4. Installation, repair or replacement in the complex of ITP equipment (individual heating points) and in the presence of booster pumping units |
||
|
1.5. Repair or replacement of the gas supply system, including: |
||
|
1.5.1. Repair or replacement of intra-house distributing highways and risers; |
||
|
1.5.2. Replacement of shut-off and control valves, including those on a branch from risers to household gas appliances in residential premises; |
||
|
1.6. Repair or replacement of the power supply system, including: |
||
|
1.6.1. Repair or replacement of main switchboard (main switchboard), distribution and group boards; |
||
|
1.6.2. Repair or replacement of intra-house distributing highways and risers of communal and apartment lighting; |
||
|
1.6.3. Replacement of branches from floor shields or boxes of apartment meters and installation and lighting fixtures for public lighting; |
||
|
1.6.4. Replacement electrical networks to power the electrical equipment of elevators and electrical equipment to ensure the operation of engineering systems; |
||
|
2. Modernization of engineering systems, including: |
||
|
2.1. Mandatory application modernized heating devices and pipelines made of plastic, metal-plastic, etc. and a ban on the installation of steel pipes |
||
|
2.2. Transfer of the existing power supply network to increased voltage; |
||
|
2.3. Replacement of lighting fixtures for public lighting needs with energy-saving ones; |
||
|
2.4. Re-equipment of heating points and water metering units; |
||
|
3. Replacing stove heating with central heating with device boiler houses, heat pipelines and thermal points; roof and other autonomous sources of heat supply |
||
|
4. Equipment systems cold and hot water supply, sewer, gas supply with accession to existing backbone networks with a distance from the input to the point of connection to the mains up to 150 m, device gas ducts, water pump, boiler rooms. |
||
|
Repair or replacement of elevator equipment recognized as unsuitable for operation, if necessary, repair of elevator shafts |
Repair and replacement of elevator equipment with its modernization, including: |
|
|
1. Repair or complete replacement of elevator equipment, recognized as unsuitable for operation; |
||
|
2. Repair, if necessary, mines, replacement of side mines; |
||
|
3. Repair of machine rooms; |
||
|
4. Repair, replacement of automation elements and scheduling of elevator equipment; |
||
|
5. Equipment of devices necessary for connection to existing systems automation and dispatching of elevator equipment |
||
|
Roof repair |
1. Repair of roof structures: |
|
|
1.1. From wooden structures: |
||
|
1.1.1. Repair: with partial replacement rafter legs, Mauerlatov Lathing solid and discharged from bars |
||
|
1.1.2. Antiseptic and fireproofing of wooden structures. |
||
|
1.1.3. Insulation of the under-roof (attic) floor |
||
|
1.1.4. Repair (replacement of dormers) |
||
|
1.2. From reinforced concrete rafters and roofing decks: |
||
|
1.2.1. Troubleshooting reinforced concrete rafters and roofing decks; |
||
|
1.2.2. Insulation of the under-roof (attic) floor |
||
|
1.2.3. Roofing screed repair; |
||
|
2. Replacement of roof coverings |
||
|
2.1. Complete replacement of the metal coating of roofs with junctions; |
||
|
2.2. Complete replacement of the roof covering from rolled bituminous materials (roofing material) for roofs from built-up materials with adjoining device |
||
|
2.3. Complete replacement of the roof covering from piece materials (slate, tiles, etc.) with adjoining device |
||
|
3. Repair or replacement of the drainage system (overhangs, gutters, grooves, trays) with the replacement of drainpipes and products (external and internal); |
||
|
4. Repair or replacement of roofing elements |
||
|
4.1. Roof hole repair |
||
|
4.2. Repair of air vents, repair or replacement of dormer windows and other devices for ventilation of the attic space; |
||
|
4.3. Change of caps on the heads of smoke ventilation blocks and ventilation shafts; |
||
|
4.4. Change of openings of parapets, firewalls, superstructures |
||
|
4.5. Repair (plastering, painting) and insulation of smoke ventilation units and elevator shafts |
||
|
4.6. Restoration or replacement of the fence on the attic roof; |
||
|
5. Reconstruction of non-ventilated combined roofs to ventilated ones with insulation of the under-roof (attic) floor |
||
|
Repair of basements belonging to common property in apartment buildings |
1. Repair of sections of basement walls and floors |
|
|
2. Insulation of walls and basement ceilings of basements |
||
|
3. Waterproofing the walls and floor of the basement |
||
|
4. Repair technical rooms with the installation of metal doors. |
||
|
5. Repair of air ducts, basement windows, pits and external doors |
||
|
6. Sealing the passages of inputs and outputs of engineering networks in the outer walls (performed during the repair of networks) |
||
|
7. Repair of the blind area |
||
|
8. Repair or replacement of the drainage system |
||
|
Warming and repair of facades |
1. Repair of facades that do not require insulation |
|
|
1.1. Repair of plaster (texture layer), including architectural order; |
||
|
1.2. Repair of facing tiles; |
||
|
1.3. Painting on plaster or on a textured layer; |
||
|
1.4. Repair and restoration of sealing of horizontal and vertical joints of wall panels of large-block and large-panel buildings; |
||
|
1.5. Repair and restoration from the side of the facade of the sealing of the joints of window and door openings of common areas; |
||
|
1.6. Painting from the side of the facade of window frames; |
||
|
1.7. Repair of enclosing walls; |
||
|
1.8. Repair and replacement of windows and balcony doors (as part of common property); |
||
|
1.9. Repair or replacement of exterior doors. |
||
|
2. Work on the repair of facades requiring insulation |
||
|
2.1. Repair and insulation of enclosing walls with subsequent surface finishing |
||
|
2.2. Repair of windows and balcony doors (as part of common property) or replacement with energy-saving design windows and doors (window blocks with triple glazing, etc.) with their subsequent insulation (sealing) |
||
|
2.3. Repair of entrance external doors with their subsequent insulation or replacement with metal doors in an energy-saving design |
||
|
3. Work common to both groups of buildings |
||
|
3.1. Repair of balconies with replacement of consoles if necessary, waterproofing and sealing with subsequent painting |
||
|
3.2. Reinforcement of canopy structures above entrances and last floors with subsequent surface finishing |
||
|
3.3. Strengthening the structures of cornice blocks with subsequent surface finishing |
||
|
3.4. Changing window sills |
||
|
3.5. Change of drainpipes |
||
|
3.6. Basement repair and insulation |
||
|
Installation of collective (common house) metering devices for resource consumption and control units (thermal energy, hot and cold water, electrical energy, gas) |
Installation of collective (common house) consumption meters: Thermal energy for the needs of heating and hot water supply; cold water consumption, electrical energy, Resource management nodes, with equipment for automation and dispatching devices to provide remote accounting and control; |
|
|
Repair of the foundations of apartment buildings. |
1. Repair or replacement of foundations. |
|
|
1.1. Sealing and jointing of joints, seams, cracks in foundation elements. Protective layer device. |
||
|
1.2. Elimination of local defects and deformations by strengthening the foundation. |
Notes:
1. During the overhaul of structures and engineering systems as part of the common property of an apartment building, as determined by Federal Law 185-FZ, at least 50% of each structure and engineering system is replaced.
2. In-house heating systems as part of common property include: risers, heating elements in common areas, in residential premises - branches from risers to the first disconnecting device (if it is not available, to the point of interface with a heater, heating element), regulating and stop valves; collective (common house) heat energy meters, as well as other equipment located on these networks.
3. In the event that during the performance of work on the overhaul of structures and engineering systems as part of the common property of MD, due to the technological and design features of the repaired (replaced) structures and engineering systems, it is necessary to dismantle or destroy parts of the property that is not part of the common property of MD , work on its restoration is carried out at the expense of capital repairs, which should be provided for in the design and estimate documentation.
4. In the event that a heating system with a hidden laying of pipelines, which is not repairable (Appendix 2), is designed in an apartment building, it is allowed to re-install a heating system with open laying of pipelines and heating appliances, heating elements, including in residential premises.
| Document's name: | |
| Document Number: | 624 |
| Type of document: | Order of the Ministry of Regional Development of Russia |
| Host body: | Ministry of Regional Development of Russia |
| Status: | current |
| Published: | |
| Acceptance date: | December 30, 2009 |
| Effective start date: | July 01, 2010 |
| Revision date: | November 14, 2011 |
MINISTRY OF REGIONAL DEVELOPMENT
RUSSIAN FEDERATION
On approval of the List of types of work on engineering surveys, on the preparation of project documentation, on the construction, reconstruction, overhaul of capital construction facilities that affect the safety of capital construction facilities
Document as amended by:
(Russian newspaper, N 180, 08/13/2010) (changes in the list of types of work come into force no earlier than six months from the date of their introduction) - see paragraph 4_1 of article 55_8 of the Town Planning Code of the Russian Federation).
(Rossiyskaya Gazeta, N 150, 07/13/2011);
(Rossiyskaya Gazeta, N 55, 03/14/2012).
____________________________________________________________________
____________________________________________________________________
This order was amended on the basis of the order of the Ministry of Regional Development of Russia dated June 9, 2010 N 275.
Order of the Ministry of Regional Development of Russia dated June 9, 2010 N 275 in accordance with clauses 18 and 19 of the Rules for the preparation of regulatory legal acts of federal executive bodies and their state registration, approved by Decree of the Government of the Russian Federation dated August 13, 1997 N 1009, is subject to registration with the Ministry of Justice of Russia and can only be applied after state registration and official publication.
- Database manufacturer's note.
____________________________________________________________________
In pursuance of Part 5 of Article 8 of the Federal Law of July 22, 2008 N 148-FZ "On Amendments to the Town Planning Code of the Russian Federation and Certain Legislative Acts of the Russian Federation" (Sobraniye Zakonodatelstva Rossiyskoy Federatsii, 2008, N 30 (part 1), Art. .3604) and in accordance with Decree of the Government of the Russian Federation of November 19, 2008 N 864 "On measures to implement the Federal Law of July 22, 2008 N 148-FZ "On Amendments to the Town Planning Code of the Russian Federation and Certain Legislative Acts of the Russian Federation" (Sobraniye zakonodatelstva Rossiyskoy Federatsii, 2008, N 48, art. 5612),
I order:
1. Approve the attached List of types of work on engineering surveys, preparation of project documentation, construction, reconstruction, overhaul of capital construction facilities that affect the safety of capital construction facilities (hereinafter - the List).
2. Establish that the List does not include the types of work on the preparation of project documentation, on construction, reconstruction, major repairs in relation to objects for which the issuance of a building permit is not required in accordance with paragraphs 1-4, 5 of part 17 of Article 51 of the Town Planning Code of the Russian Federation (Collected Legislation of the Russian Federation, 2005, N 1, Art. 16; 2006, N 1, Art. 21; 2008, N 30, Art. 3616; 2009, N 48, Art. 5711; 2010, N 48, 6246; 2011, N 13, art. 1688; N 27, art. 3880; N 30, art. 4563, art. 4572, art. housing construction(detached residential buildings with no more than three floors, intended for no more than two families); residential buildings with no more than three floors, consisting of several blocks, the number of which does not exceed ten and each of which is intended for one family, has a common wall (common walls) without openings with the neighboring block or neighboring blocks, is located on a separate land plot and has access to the common area ( residential buildings blocked building); apartment buildings with no more than three floors, consisting of one or more block sections, the number of which does not exceed four, each of which contains several apartments and common areas and each of which has a separate entrance with access to the common area.
(Paragraph as amended, put into effect on March 25, 2012 by order of the Ministry of Regional Development of Russia dated November 14, 2011 N 536.
Types of work on the preparation of project documentation contained in the List can be performed individual entrepreneur independently (personally), and the types of work on engineering surveys, construction, reconstruction, overhaul - only with the involvement of employees in the manner prescribed by the legislation of the Russian Federation ).
3. Recognize invalid the order of the Ministry of Regional Development of the Russian Federation dated December 9, 2008 N 274 "On approval of the List of types of work on engineering surveys, on the preparation of project documentation, on the construction, reconstruction, overhaul of capital construction facilities that affect the safety of facilities capital construction" (registered with the Ministry of Justice of Russia on January 16, 2009 N 13086), as well as the order of the Ministry of Regional Development of the Russian Federation of October 21, 2009 N 480 "On Amendments to the Order of the Ministry of Regional Development of the Russian Federation of December 9, 2008 N 274" On approval of the List of types of work on engineering surveys, on the preparation of project documentation, on the construction, reconstruction, overhaul of capital construction facilities that affect the safety of capital construction facilities "(registered in the Ministry of Justice of Russia on December 22, 2009 N 15789) from the date of entry into force of this order.
5. The control of the execution of this order shall be entrusted to the Deputy Minister of Regional Development of the Russian Federation V.A. Tokarev.
Minister
V.Basargin
Registered
at the Ministry of Justice
Russian Federation
April 15, 2010
registration N 16902
1. Works as part of engineering and geodetic surveys
1.1. Creation of reference geodetic networks
1.2. Geodetic observations of deformations and settlements of buildings and structures, movements of the earth's surface and dangerous natural processes
1.3. Creation and updating of engineering and topographic plans on a scale of 1:200-1:5000, including in digital form, survey of underground utilities and structures
1.4. Line feature tracing
1.5. Engineering and hydrographic works
1.6. Special geodetic and topographic work in the construction and reconstruction of buildings and structures
2. Works as part of engineering and geological surveys
2.1. Engineering-geological survey on a scale of 1:500-1:25000
2.2. Sinking of mine workings with their testing, laboratory studies of the physical and mechanical properties of soils and chemical properties of groundwater samples
2.3. The study of dangerous geological and engineering-geological processes with the development of recommendations for the engineering protection of the territory
2.4. Hydrogeological research
2.5. Geophysical surveys
2.6. Engineering geocryological research
2.7. Seismological and seismotectonic studies of the territory, seismic microzoning
3. Works as part of engineering and hydrometeorological surveys
3.1. Meteorological observations and study of the hydrological regime of water bodies
3.2. Study of dangerous hydrometeorological processes and phenomena with calculations of their characteristics
3.3. Study of channel processes of water bodies, deformations and processing of banks
3.4. Studies of the ice regime of water bodies
4. Works as part of engineering and environmental surveys
4.1. Engineering and environmental survey of the territory
4.2. Studies of chemical pollution of soils, surface and ground waters, atmospheric air, sources of pollution
4.3. Laboratory chemical-analytical and gas-chemical studies of samples and samples of soil and water
4.4. Research and assessment of physical impacts and radiation situation on the territory
4.5. Study of vegetation, wildlife, sanitary-epidemiological and medical-biological studies of the territory*
_______________
.
5. Works as part of engineering and geotechnical surveys
(Performed as part of engineering-geological surveys or separately on the territory studied in engineering-geological terms for separate buildings and structures)
5.1. Sinking of mine workings with their testing and laboratory studies of the mechanical properties of soils with the determination of characteristics for specific schemes for calculating the bases of foundations
5.2. Field tests of soils with the determination of their standard strength and deformation characteristics (stamp, shear, pressuremeter, shear). Tests of reference and full-scale piles
5.3. Determination of standard mechanical characteristics of soils by methods of static, dynamic and drilling sounding
5.4. Physical and mathematical modeling of the interaction of buildings and structures with the geological environment
5.5. Special studies of soil characteristics according to individual programs for non-standard, including nonlinear methods calculation of the bases of foundations and structures of buildings and structures
5.6. Geotechnical control of construction of buildings, structures and adjacent territories
6. Inspection of the state of soils of the foundation of buildings and structures
7. The item was excluded from January 14, 2012 by order of the Ministry of Regional Development of Russia dated May 26, 2011 N 238 ..
1. Work on the preparation of a scheme for the planning organization of a land plot:
1.1. Preparation work master plan land plot
1.2. Works on the preparation of a planning organization scheme for the route of a linear facility
1.3. Works on the preparation of the scheme of planning organization of the right of way of the linear structure
2. Work on the preparation of architectural solutions
3. Work on the preparation of constructive solutions
4. Work on the preparation of information on internal engineering equipment, internal networks of engineering and technical support, on the list of engineering and technical measures:
4.1. Works on the preparation of projects for internal engineering systems of heating, ventilation, air conditioning, smoke ventilation, heat supply and refrigeration
4.2. Works on the preparation of projects for internal engineering systems of water supply and sewerage
4.3. Project preparation works internal systems power supply*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
4.4. Works on the preparation of projects for internal low-voltage systems*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
4.5. Works on the preparation of projects for internal dispatching, automation and management of engineering systems
4.6. Works on the preparation of projects for internal gas supply systems
5. Work on the preparation of information on external networks of engineering and technical support, on the list of engineering and technical measures:
5.1. Works on the preparation of projects for external heat supply networks and their structures
5.2. Works on the preparation of projects for external water supply and sewerage networks and their structures
5.3. Works on the preparation of projects for external power supply networks up to 35 kV inclusive and their structures
5.4. Works on the preparation of projects for external power supply networks of not more than 110 kV inclusive and their structures
5.5. Works on the preparation of projects for external power supply networks of 110 kV and more and their structures
5.6. Works on the preparation of projects for external networks of low-voltage systems
5.7. Works on the preparation of projects for external gas supply networks and their structures
6. Work on the preparation of technological solutions:
6.1. Works on the preparation of technological solutions for residential buildings and their complexes
6.2. Works on the preparation of technological solutions for public buildings and structures and their complexes
6.3. Works on the preparation of technological solutions for industrial buildings and structures and their complexes
6.4. Works on the preparation of technological solutions for transport facilities and their complexes
6.5. Works on the preparation of technological solutions for hydraulic structures and their complexes
6.6. Works on the preparation of technological solutions for agricultural facilities and their complexes
6.7. Works on the preparation of technological solutions for special-purpose facilities and their complexes
6.8. Works on the preparation of technological solutions for oil and gas facilities and their complexes
6.9. Works on the preparation of technological solutions for objects of collection, processing, storage, processing and disposal of waste and their complexes
6.10. Works on the preparation of technological solutions for nuclear power and industry facilities and their complexes
6.11. Work on the preparation of technological solutions for military infrastructure facilities and their complexes
6.12. Works on the preparation of technological solutions for treatment facilities and their complexes
6.13. Works on the preparation of technological solutions for metro facilities and their complexes
7. Work on the development of special sections of project documentation:
7.1. Engineering and technical measures for civil defense
7.2. Engineering and technical measures to prevent natural and man-made emergencies
7.3. Development of a declaration on industrial safety of hazardous production facilities
7.4. Development of a declaration of safety of hydraulic structures
7.5. Development of justification for radiation and nuclear protection
8. Works on the preparation of projects for the organization of construction, demolition and dismantling of buildings and structures, extension of the service life and conservation *
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
9. Work on the preparation of draft measures for environmental protection
10. Works on the preparation of draft measures to ensure fire safety
11. Work on the preparation of draft measures to ensure access for people with limited mobility
12. Work on the inspection of building structures of buildings and structures
13. Works on organizing the preparation of project documentation by the involved developer or customer on the basis of an agreement by a legal entity or an individual entrepreneur (general designer)
1. Geodetic works performed on construction sites
1.1. Layout work in the process of construction*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
1.2. Geodetic control of the accuracy of the geometric parameters of buildings and structures*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
2. Preparatory work
2.1. Dismantling (dismantling) of buildings and structures, walls, ceilings, flights of stairs and other structural and related elements or parts thereof*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
2.2. Construction of temporary: roads; sites; engineering networks and structures*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
2.3. Installation of rail crane tracks and foundations (supports) of stationary cranes
2.4. Installation and dismantling of inventory external and internal scaffolding, technological garbage chutes*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
3. Earthworks
3.1. Mechanized excavation*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
3.2. Soil excavation and drainage arrangement in water management construction
3.3. Soil development by hydromechanization
3.4. Works on artificial freezing of soils
3.5. Soil compaction with rollers, compactors or heavy rammers*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
3.6. Mechanized loosening and development of permafrost soils
3.7. Works on dewatering, organization of surface runoff and drainage
4. Construction of wells
4.1. Drilling, construction and installation of oil and gas wells
4.2. Drilling and construction of wells (except for oil and gas wells)
4.3. Fixing wells with pipes, extracting pipes, free lowering or lifting pipes from wells
4.4. Plugging works
4.5. Construction of mine wells
5. Pile work. Soil stabilization
5.1. Pile work performed from the ground, including in sea and river conditions
5.2. Pile work performed in frozen and permafrost soils
5.3. Grillage device
5.4. Installation of driven and bored piles
5.5. Thermal strengthening of soils
5.6. Cementation of soil bases with driving injectors
5.7. Silicization and resinization of soils
5.8. Works on the construction of structures using the "wall in the ground" method
5.9. Driving and lifting steel and sheet piles
6. Installation of concrete and reinforced concrete monolithic structures
6.1. Formwork
6.2. Reinforcing works
6.3. Installation of monolithic concrete and reinforced concrete structures
7. Installation of prefabricated concrete and reinforced concrete structures
7.1. Installation of foundations and structures of the underground part of buildings and structures
7.2. Installation of structural elements of the above-ground part of buildings and structures, including columns, frames, crossbars, trusses, beams, slabs, belts, wall panels and partitions
7.3. Installation of volumetric units, including ventilation units, elevator shafts and garbage chutes, sanitary cabins
8. Drilling and blasting during construction
9. Works on the device of stone structures
9.1. Arrangement of structures of buildings and structures made of natural and artificial stones, including those with cladding*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
9.2. Installation of brick structures, including those with cladding*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
9.3. Arrangement of heating furnaces and hearths*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
10. Installation of metal structures
10.1. Installation, strengthening and dismantling of structural elements and enclosing structures of buildings and structures
10.2. Installation, reinforcement and dismantling of structures of transport galleries
10.3. Installation, strengthening and dismantling of tank structures
10.4. Installation, strengthening and dismantling of mast structures, towers, exhaust pipes
10.5. Installation, reinforcement and dismantling of technological structures
10.6. Mounting and dismantling of cable supporting structures (stretch marks, cable-stayed structures, etc.)
11. Installation of wooden structures
11.1. Installation, strengthening and dismantling of structural elements and enclosing structures of buildings and structures, including those made of glued structures*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
11.2. Assembly of residential and public buildings from prefabricated parts of a complete delivery*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
12. Protection of building structures, pipelines and equipment (except for main and field pipelines)
12.1. Lining works
12.2. Masonry made of acid-resistant bricks and shaped acid-resistant ceramic products
12.3. Protective coating with paintwork materials*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
12.4. Gumming (lining with sheet rubber and liquid rubber compounds)
12.5. Glue insulation device
12.6. The device of metallization coatings
12.7. Application of a front coating when installing a monolithic floor in rooms with aggressive environments
12.8. Antiseptic treatment of wooden structures
12.9. Waterproofing of building structures
12.10. Works on thermal insulation of buildings, building structures and equipment
12.11. Works on thermal insulation of pipelines*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
12.12. Works on fire protection of building structures and equipment
13. Roofing
13.1. Installation of roofs from piece and sheet materials*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
13.2. Roofing from roll materials*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
13.3. Self-leveling roofing*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
14. Facade works
14.1. Surface cladding with natural and artificial stones and linear shaped stones*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
14.2. Installation of ventilated facades*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
15. Arrangement of internal engineering systems and equipment of buildings and structures
15.1. Installation and dismantling of the water supply and sewerage system *
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
15.2. Installation and dismantling of the heating system *
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
15.3. Installation and dismantling of the gas supply system
15.4. Installation and dismantling of the ventilation and air conditioning system *
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
15.5. The device of the power supply system *
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
15.6. Arrangement of electrical and other control networks for life support systems of buildings and structures*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
16. Installation of external water supply networks
16.1. Laying of water pipelines
16.2. Installation and dismantling of shut-off valves and equipment for water supply networks
16.3. Installation of water wells, caps, catchment dampers
16.4. Cavity cleaning and testing of water pipelines
17. Construction of external sewer networks
17.1. Laying of non-pressure sewer pipelines
17.2. Laying sewer pressure pipelines
17.3. Installation and dismantling of shut-off valves and equipment of sewer networks
17.4. Installation of sewer and drain wells
17.5. Arrangement of a filtering base for silt pads and filtration fields
17.6. Laying drainage pipes on sludge beds
17.7. Cavity cleaning and testing of sewer pipelines
18. Construction of external heat supply networks
18.1. Laying of heat supply pipelines with a coolant temperature of up to 115 degrees Celsius
18.2. Laying of heat supply pipelines with a coolant temperature of 115 degrees Celsius and above
18.3. Installation and dismantling of shutoff valves and equipment of heat supply networks
18.4. Arrangement of wells and chambers of heat supply networks
18.5. Cavity cleaning and testing of heating pipelines
19. The device of external gas supply networks, except for the main
19.1. Laying of gas pipelines with working pressure up to 0.005 MPa inclusive
19.2. Laying of gas pipelines with working pressure from 0.005 MPa to 0.3 MPa inclusive
19.3. Laying of gas pipelines with working pressure from 0.3 MPa to 1.2 MPa inclusive (for natural gas), up to 1.6 MPa inclusive (for liquefied petroleum gas)
19.4. Installation of condensate collectors for hydraulic seals and compensators on gas pipelines
19.5. Installation and dismantling of gas control points and installations
19.6. Installation and dismantling of tank and group cylinder installations of liquefied gas
19.7. Entering the gas pipeline into buildings and structures
19.8. Installation and dismantling of gas equipment for consumers using natural and liquefied gas
19.9. Tapping under pressure into existing gas pipelines, disconnection and plugging under pressure of existing gas pipelines
19.10. Cavity cleaning and testing of gas pipelines
20. Arrangement of external electrical networks and communication lines
20.1. Arrangement of power supply networks with voltage up to 1 kV inclusive *
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
20.2. Arrangement of power supply networks with voltage up to 35 kV inclusive
20.3. Arrangement of power supply networks with voltage up to 330 kV inclusive
20.4. Construction of power supply networks with voltage over 330 kV
20.5. Installation and dismantling of supports for overhead power lines with voltage up to 35 kV
20.6. Installation and dismantling of supports for overhead power lines with voltage up to 500 kV
20.7. Installation and dismantling of supports for overhead power lines with a voltage of more than 500 kV
20.8. Installation and dismantling of wires and lightning protection cables of overhead power lines with voltage up to 35 kV inclusive
20.9. Installation and dismantling of wires and lightning protection cables of overhead power lines with voltage over 35 kV
20.10. Installation and dismantling of transformer substations and linear electrical equipment with voltage up to 35 kV inclusive
20.11. Installation and dismantling of transformer substations and linear electrical equipment with voltage over 35 kV
20.12. Installation of distribution devices, switching equipment, protection devices
20.13. Arrangement of external communication lines, including telephone, radio and television*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
21. Arrangement of nuclear facilities
21.1. Works on the construction of facilities with nuclear installations
21.2. Works on the construction of nuclear weapons complex facilities
21.3. Works on the construction of elementary particle accelerators and hot chambers
21.4. Works on the construction of storage facilities for nuclear materials and radioactive substances, storage facilities for radioactive waste
21.5. Works on the construction of nuclear fuel cycle facilities
21.6. Works on the construction of facilities for the extraction and processing of uranium
21.7. Works on decommissioning of nuclear facilities
(Clause 21 as amended, put into effect on December 23, 2010 by order of the Ministry of Regional Development of Russia dated June 23, 2010 N 294.
22. Arrangement of oil and gas industry facilities
22.1. Installation of main and field pipelines
22.2. Works on the arrangement of oil and gas preparation facilities for transport
22.3. Arrangement of oil depots and gas storage facilities
22.4. Arrangement of crossing structures under linear objects (roads and railways) and other obstacles of natural and artificial origin
22.5. Works on the construction of crossings by the method of directional drilling
22.6. Device for electrochemical protection of pipelines
22.7. Tapping under pressure into existing main and field pipelines, disconnection and plugging under pressure of existing main and field pipelines
22.8. Performance of anti-corrosion protection and insulation works in relation to main and field pipelines
22.9. Works on the development of oil and gas fields offshore
22.10. Works on the construction of gas filling compressor stations
22.11. Quality control of welded joints and their isolation
22.12. Cavity cleaning and testing of main and field pipelines
23. Installation work
23.1. Installation of handling equipment
23.2. Elevator installation
23.3. Installation of equipment for thermal power plants
23.4. Installation of boiler room equipment
23.5. Installation of compressor units, pumps and fans*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
23.6. Installation of electrical installations, equipment, automation and alarm systems*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
23.7. Installation of equipment for nuclear facilities
23.8. Installation of equipment for cleaning and preparation for the transportation of gas and oil
23.9. Installation of equipment for oil and gas pumping stations and for other product pipelines
23.10. Installation of natural gas liquefaction equipment
23.11. Installation of gas station equipment
23.12. Installation of equipment for ferrous metallurgy enterprises
23.13. Installation of equipment for non-ferrous metallurgy enterprises
23.14. Installation of equipment for the chemical and oil refining industries
23.15. Installation of mining and ore-dressing equipment
23.16. Installation of equipment for railway infrastructure facilities
23.17. Installation of subway and tunnel equipment
23.18. Installation of equipment for hydroelectric stations and other hydraulic structures
23.19. Installation of equipment for electrical industry enterprises
23.20. Installation of equipment for enterprises in the building materials industry
23.21. Installation of equipment for the pulp and paper industry
23.22. Installation of equipment for textile industry enterprises
23.23. Installation of equipment for printing industry enterprises
23.24. Installation of equipment for food industry enterprises*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
23.25. Installation of equipment for theater and entertainment enterprises
23.26. Installation of equipment for granaries and grain processing enterprises
23.27. Installation of equipment for cinematography enterprises*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
23.28. Installation of equipment for enterprises in the electronics industry and the communications industry*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
23.29. Installation of equipment for healthcare institutions and medical industry enterprises*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
23.30. Installation of equipment for agricultural production, including fish processing and fish storage*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
23.31. Installation of equipment for consumer services and public utilities *
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
23.32. Installation of water intake equipment, sewerage and treatment facilities
23.33. Installation of equipment for communication facilities*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
23.34. Installation of equipment for space infrastructure facilities
23.35. Installation of airport equipment and other aviation infrastructure facilities
23.36. Installation of equipment for sea and river ports
24. Commissioning
24.1. Commissioning of lifting and transport equipment
24.2. Commissioning of elevators
24.3. Commissioning of synchronous generators and excitation systems
24.4. Commissioning of power and instrument transformers
24.5. Commissioning of switching devices
24.6. Commissioning of relay protection devices
24.7. Commissioning of automation in power supply *
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
24.8. Commissioning of voltage and control current systems
24.9. Commissioning of electrical machines and electric drives
24.10. Commissioning of automation systems, alarm systems and related devices*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
24.11. Start-up and adjustment works of stand-alone systems adjustment*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
24.12. Commissioning works of complex adjustment of systems*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
24.13. Commissioning of telemechanics*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
24.14. Adjustment of ventilation and air conditioning systems*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
24.15. Commissioning of automatic machine lines
24.16. Commissioning of multi-purpose metal-cutting machines with CNC
24.17. Commissioning of unique metal-cutting machines weighing over 100 tons
24.18. Commissioning of refrigeration units*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
24.19. Commissioning of compressor units
24.20. Commissioning of steam boilers
24.21. Commissioning of hot water boilers*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
24.22. Commissioning works of auxiliary boiler equipment*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
24.23. Commissioning of water treatment equipment and chemical water treatment equipment
24.24. Start-up and adjustment works of technological installations of the fuel economy
24.25. Commissioning of the gas-air path
24.26. Commissioning of general boiler systems and utilities
24.27. Commissioning of equipment for processing and finishing wood
24.28. Commissioning of drying plants
24.29. Commissioning works of water supply facilities
24.30. Commissioning works of sewerage facilities
24.31. Commissioning works at the facilities of the oil and gas complex
24.32. Commissioning work at nuclear facilities (the item was additionally included from December 23, 2010 by order of the Ministry of Regional Development of Russia dated June 23, 2010 N 294)
25. Arrangement of roads and airfields *
________________
*Probably an original error. It should read: "aerodromes". - Database manufacturer's note.
25.1. Works on the construction of subgrade for highways, airport platforms, runways, taxiways
25.2. The device of the bases of highways
25.3. Arrangement of foundations for airport aprons, runways, taxiways
25.4. Road pavement devices, including those reinforced with binders
25.5. Devices for covering airport aprons, runways, taxiways
25.6. Installation of drainage, catchment, culvert, spillway devices
25.7. Installation of protective fences and elements of arrangement of highways
25.8. Road marking device
26. Arrangement of railway and tram tracks
26.1. Works on the construction of subgrade for railway tracks
26.2. Works on the construction of subgrade for tram tracks
26.3. The device of the upper structure of the railway track
26.4. Arrangement of drainage and protective structures of the subgrade of the railway track
26.5. Installation of signaling, centralization and blocking of railways
26.6. Railway electrification
26.7. Stabilization of soils in the right of way of the railway
26.8. Construction of railway crossings
27. Construction of tunnels, subways
27.1. Sinking of tunnels and subways without the use of special methods of tunneling
27.2. Excavation of tunnels and subways using artificial freezing
27.3. Sinking of tunnels and subways using grouting
27.4. Sinking of tunnels and subways with the use of electrochemical fastening
27.5. Sinking of tunnels and subways with the use of lowering support
27.6. Arrangement of internal structures of tunnels and subways
27.7. Subway track arrangement
28. Installation of mine structures
28.1. Sinking of the development of mine structures without the use of special methods of sinking
28.2. Sinking of the development of mine structures using artificial freezing
28.3. Sinking of the development of mine structures with the use of grouting
28.4. Sinking of the development of mine structures with the use of electrochemical fastening
28.5. Sinking of the development of mine structures with the use of lowering lining
29. Arrangement of bridges, overpasses and overpasses
29.1. Installation of monolithic reinforced concrete and concrete structures of bridges, flyovers and overpasses
29.2. Arrangement of prefabricated reinforced concrete structures of bridges, flyovers and overpasses
29.3. Construction of pedestrian bridges
29.4. Installation of steel superstructures of bridges, flyovers and overpasses
29.5. Installation of wooden bridges, flyovers and overpasses
29.6. Installation of stone bridges, flyovers and overpasses
29.7. Laying culvert pipes on finished foundations (bases) and drainage trays
30. Hydraulic works, diving works
30.1. Development and movement of soil by jet and floating dredgers
30.2. Loosening and development of soils under water in a mechanized way and issuance to a dump or floating facilities
30.3. Drilling and construction of wells under water
30.4. Piling work performed in marine conditions from floating facilities, including the installation of shell piles
30.5. Pile work performed in river conditions from floating facilities, including the installation of shell piles
30.6. Construction of structures in sea and river conditions from natural and artificial massifs
30.7. Construction of dams
30.8. Installation, dismantling of building structures in underwater conditions
30.9. Laying pipelines in underwater conditions
30.10. Laying cables in underwater conditions, including electrical and communication
30.11. Diving (underwater construction) works, including quality control of hydrotechnical works under water
31. Industrial furnaces and chimneys
31.1. Blast furnace masonry
31.2. Masonry of the upper structure of glass melting furnaces
31.3. Installation of furnaces from prefabricated elements of increased factory readiness
31.4. Electrolyzers for the aluminum industry
31.5. Lining of industrial flue and ventilation furnaces and pipes
32. Implementation work building control attracted by the developer or customer on the basis of an agreement by a legal entity or individual entrepreneur
32.1. Construction control for general construction works(groups of types of work N 1-3, 5-7, 9-14)
32.2. Construction control over well construction works (group of types of work N 4)
32.3. Construction control over drilling and blasting (group of types of work N 8)
32.4. Construction control over work in the field of water supply and sewerage (type of work N 15.1, 23.32, 24.29, 24.30, groups of types of work N 16, 17)
32.5. Construction control over work in the field of heat and gas supply and ventilation (types of work N 15.2, 15.3, 15.4, 23.4, 23.5, 24.14, 24.19, 24.20, 24.21, 24.22, 24.24, 24.25, 24.26, groups of types of work N 18, 19)
32.6. Construction control over work in the field of fire safety (type of work N 12.3, 12.12, 23.6, 24.10-24.12)
32.7. Construction control over work in the field of power supply (type of work N 15.5, 15.6, 23.6, 24.3-24.10, group of types of work N 20)
32.8. Construction control during the construction, reconstruction and overhaul of communication facilities (types of work N 20.13, 23.6, 23.28, 23.33, 24.7, 24.10, 24.11, 24.12) 2010 N 294
32.9. Construction control during the construction, reconstruction and overhaul of oil and gas industry facilities (type of work N 23.9, 23.10, group of types of work N 22)
32.10. Construction control during the construction, reconstruction and overhaul of roads and airfields, bridges, flyovers and overpasses (type of work N 23.35, groups of types of work N 25, 29)
32.11. Construction control during the construction of railway and tram tracks (types of work N 23.16, group of types of work N 26)
32.12. Construction control during construction, reconstruction and overhaul in underground conditions (types of work N 23.17, groups of types of work N 27, 28)
32.13. Construction control over hydraulic engineering and diving works (group of types of work N 30)
32.14. Construction control during the construction, reconstruction and overhaul of industrial furnaces and chimneys (group of types of work N 31)
32.15. The item was excluded from December 23, 2010 by order of the Ministry of Regional Development of Russia dated June 23, 2010 N 294 ..
33. Works on the organization of construction, reconstruction and overhaul by the attracted developer or customer on the basis of an agreement by a legal entity or an individual entrepreneur (general contractor):
33.1. Industrial engineering
33.1.1. Enterprises and facilities of the fuel industry
33.1.2. Enterprises and facilities of the coal industry
33.1.3. Enterprises and objects of ferrous metallurgy
33.1.4. Enterprises and objects of non-ferrous metallurgy
33.1.5. Enterprises and objects of the chemical and petrochemical industry
33.1.6. Enterprises and objects of mechanical engineering and metalworking
33.1.7. Enterprises and facilities of the forestry, woodworking, pulp and paper industries
33.1.8. Enterprises and objects of light industry*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
33.1.9. Enterprises and facilities of the food industry*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
33.1.10. Enterprises and objects of agriculture and forestry*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
33.1.11. Thermal power plants
33.1.12. Nuclear facilities
33.1.13. Power supply facilities over 110 kV
33.1.14. Oil and gas facilities
33.2. Transport construction
33.2.1. Roads and road transport infrastructure
33.2.2. Railways and railway infrastructure facilities
33.2.3. Airports and other aviation infrastructure facilities
33.2.4. Road and rail tunnels
33.2.5. Subways
33.2.6. Bridges (large and medium)
33.2.7. Enterprises and facilities public transport*
_______________
* These types and groups of types of work require obtaining a certificate of admission to types of work that affect the safety of a capital construction object, if such work is performed at the facilities specified in Article 48_1 of the Town Planning Code of the Russian Federation.
33.3. Housing and civil construction
33.4. Power supply facilities up to 110 kV inclusive
33.5. Heat supply facilities
33.6. Gas supply facilities
33.7. Water supply and sewerage facilities
33.8. Buildings and facilities of communication facilities
33.9. Maritime transport facilities
33.10. River transport facilities
33.11. Hydropower facilities
33.12. Dams, dams, canals, bank protection structures, reservoirs (with the exception of hydropower facilities)
33.13. hydromeliorative facilities.
34. Works on the implementation of construction control by the developer, or by a legal entity or individual entrepreneur engaged by the developer or customer on the basis of an agreement during the construction, reconstruction and overhaul of nuclear facilities (types of work N 23.7, 24.32, group of types of work N 21) (additional clause included from December 23, 2010 by order of the Ministry of Regional Development of Russia dated June 23, 2010 N 294)
Revision of the document, taking into account
changes and additions prepared
JSC "Kodeks"
| Document's name: | On approval of the List of types of work on engineering surveys, preparation of project documentation, construction, reconstruction, overhaul of capital construction facilities that affect the safety of capital construction facilities (as amended on November 14, 2011) |
| Document Number: | 624 |
| Type of document: | Order of the Ministry of Regional Development of Russia |
| Host body: | Ministry of Regional Development of Russia |
| Status: | current |
| Published: | Russian newspaper, N 88, 04/26/2010 |
| Acceptance date: | December 30, 2009 |
| Effective start date: | July 01, 2010 |
| Revision date: | November 14, 2011 |
Construction - a key term for the industry of the same name, denoting the process of erecting buildings and structures. This is a very broad concept that also includesoverhaul andrestoration . The main difference between construction and reconstruction lies not only in the scope of concepts. Usually, construction is understood as the construction of an object from scratch, which, accordingly, requires a lot of preparatory work- this is design, off-site and on-site work, specific approvals, etc. When developing, it is necessary to take into account such factors as geodetic conditions, the presence of adjacent buildings, features of urban zoning, and much more.
Reconstruction is carried out on an already finished object, therefore, during reconstruction, the characteristics of this particular object are taken into account in the first place. Construction ends with the commissioning of the constructed building or structure. The purpose of the reconstruction is to restore the object and often to adapt it to use in new conditions. As a result of the reconstruction, the main technical and economic characteristics of the building are changed.
The term "reconstruction" must also be distinguished from the term "overhaul". According to Urban Planning Code RF, major repairs, unlike reconstruction, do not change the main indicators of the object. After reconstruction in buildings and structures (including linear facilities), for example, the built-up area, building volume, number of floors, usable area may increase. It is believed that the terms of reconstruction and overhaul should coincide, however, in practice, reconstruction requires a larger number of approvals and permits that must be obtained from various authorities. A major overhaul changes a building only in the sense that it eliminates physical or moral wear and tear. As part of the overhaul, repairs of the internal communications of the building, repair of the foundation, basement, roof, walls, facades, elevators and elevator shafts can be performed. Also, the list of repairs can be expanded with such items as: facade insulation, installation of metering devices, arrangement of exits to the roof, etc. Another task of a major overhaul is not only to nullify the existing physical and moral deterioration, but also to bring the building or structure in line with modern standards.
Construction, reconstruction and overhaul works It is not always easy to distinguish between them. Considering that the construction industry is constantly enriched with new materials and technologies, disputes sometimes arise whether the characteristics of the building have changed as a result of the work carried out and whether they relate to reconstruction or overhaul (for example, replacing wooden floors with reinforced concrete). Legal literacy, especially in the field of capital construction, is required to prevent a stoppage of construction and solve problems associated with a different understanding of the concepts of reconstruction and overhaul.
The Interregional Academy of Additional Professional Education (MADPO) offers high-quality training in professional retraining or advanced training courses in the specialty "Construction, reconstruction and overhaul" . Anyone who already has a higher professional education in the field of construction can become students of the courses. Within the framework of the specialty, training is possible in the following programs:
Table
During the course, students will explore a number of topics, including the following:
Courses last 252 or 520 hours depending on the choice of listeners. The training ends with the final certification and issuance diploma of the established sample on the completion of a professional retraining course.
The duration of the program is 72 or 150 teaching hours. The course is designed to improve the professional competence of specialists in the field of construction, reconstruction and overhaul. Following the results of training, documents are issued: certificate of the established sample on the completion of advanced training courses.
